• 16 Ga. x 36" Niagara Initial Type Motor Driven Pinch Roll

    No price - Farmingdale, NY, USA
    • Manufacturer: Niagara

    equipped with: electric foot pedal, manual roll adjustment, forward & reverse, rolls grooved for wire

  • Ridgid Manual Tubing

    No price - Riverside, CA, USA
    • Manufacturer: Ridgid

    (1) #368 & (1) #508; (loc. maint.) commercial kitchen for soups, sauces, pastas, and pizzas including cooking systems, pasta cookers, ovens, parfait cup filler, packaging lines, and much more

  • 10" Cap 48" Width Hendley & Whittemore 48-10 BENDING ROLL

    $6,950 - Harrison, NJ, USA
    • Manufacturer: Hendley & Whittemore

    4' x 10 gauge hendley whittmore mechanical bending roll s/n 12437 length .................................. 48" capacity ................................ 10 ga. roll diameter .........................

  • ERCOLINA TM76-20 1-1/4" PIPE

    No price - New City, NY, USA
    • Manufacturer: Ercolina

    see attachment for capacities 76.2 x 3.2 mm capacity 2 2" gas inches (5.6 mm) capacity 64 x 64 x 2.5 mm square tube capacity maximum bending radius 250 mm minimum bending radius 1.5 x o control off...

  • 7 FT. X 14 GA. SURIANOS PLATE BENDING ROLL

    No price - Elk Grove Village, IL, USA

      7 ft. x 14 ga. surianos plate bending roll initial type capacity: 7' x 14 ga. mild steel roll diameter: 4-3/4" roll length: 84" pass line: 35" equipped with: manual drop end power rear roll adjustm...

    • 2" x 2" x 1/4", ZOPF, #ZB 70/2 M, 1.46 HP, 2" sched. 40, manual adjustment, 2001

      No price - Hialeah, FL, USA

        technical specifications: shaft diameters 1-5/8" (40mm) roll diameters 6-3/8" nominal drive motor 1.46 hp (1.1 kw) electrics--standard 220 volt, 3 ph phase, 60 hz powered rolls two rolls driven pos...

      • 2004 HOMAG KAL 310/3/A3 EDGEBANDER (HIGH PRODUCTION)

        $41,232 - Charlotte, NC, USA
        • Manufacturer: Homag

        elect./voltage: 600 v, 60 cy, 3 ph homag kal 310/3/a3 multi-coils single sided edgebander 0.4 - 3 mm edge thickness cap., min. panel width 55 mm; maximum panel thickness 55 mm;technical specificati...

      • 1-1/8" PINES MODEL #MC-1400 TUBE BENDER

        No price - Newark, NJ, USA
        • Manufacturer: Pines

        specifications: mandrel length: 72" radius of bend: 8" max equipped with: - counter clockwise bending - manual clamping - hydraulic operation - degree of bend - hand lever control - self cont. h...

      • Craig and Donald 5" x 5" x 3/4" Angle Bending Roll

        No price - Indian Trail, NC, USA
        • Manufacturer: Craig and Donald
        • Capacity: 4" x 4" x 3/4"

        equipped with: hydraulic drive to rolls*power adjustable top roll w/ out board support*manual adjustable guide rolls*push button controls*standard set of bending rolls

      • BUFFALO #1 HORZONTAL BENDING ROLLS

        No price - Newark, NJ, USA
        • Manufacturer: Buffalo

        manual height adjustment of upper roll manual vertical & lateral adjustment of guide rolls four set of angle rolls miscelaneous space plates four set od radious rolls 10 hp motor, wired 3 phase, 60...