Used bending rolls

- 2084 listings found
Sort by Price: Low to High | High to Low
  • 1996 Roundo R-13S Angle Bending Rolls

    • Manufacturer: Roundo

      Reduced price this machine has several hundred thousand dollars in tooling. machine is in good condition and running. tooling listed at the bottom of this quote. additional tooling has been made for this mach...

      No price
      Venetia, PA, USA
    • 12 Ga. x 48" Webb Power Plate Bending Roll

      • Manufacturer: Webb

        12 ga. x 48" webb model 450 power plate bending roll; s/n 6510, 70 mm rear roll adj., 4-1/4" approx roll diameter, drop end, pb control, overhead roll support frame, approx. dimensions: 11' x 6' x 7'

        $4,950 (USD)
        Cincinnati, OH, USA
      • 3" X 3" X 3/8" STECO ANGLE BENDING ROLL

            Used 3" x 3" x 3/8" steco angle bending roll model no. sbm/3 with leg-in and leg-out attachment capacities: angles - leg out: 3" x 3" x 3/8" - minimum dia. 24" mild steel angles - leg in: 2.5" x 2.5" x 3/8"-min. ...

            No price
            Elk Grove Village, IL, USA
          • 4" X 4" X 5/8" BUFFALO ANGLE BENDING ROLL

            • Manufacturer: Buffalo

              Used 4" x 4" x 5/8" buffalo angle bending roll model no. 2 with leg-in and leg-out attachment capacities: angles - leg out: 4" x 4" x 5/8" - minimum dia. 40" mild steel angles - leg in: 3.5" x 3.5" x 5/8" -min. d...

              No price
              Elk Grove Village, IL, USA
            • 1952 WEBB 1/4" x 96" R3L Initial Pinch Plate Bending Roll

              • Manufacturer: Webb
              • Model: R3L

                Equipped with: power rear roll adjustment, drop end, electric foot switch, forward & reverse

                No price
                Farmingdale, NY, USA
              • 2000 Tauring Angle Bending Roll Delta 50H

                • Manufacturer: Delta

                  comments: round tube - size: 3.15” x .080” / min. radius 44” square tube - size: 2.3” x 2.3” x .2” / min. radius 51” flat bar (hard way) - size: 3.15” x .60” / min. radius 35” flat bar (easy way) - size:4.7" x 1...

                  $8,950 (USD)
                  Elk River, MN, USA
                • Somo Angle Bending Roll #2548

                  • Manufacturer: Somo

                    Somo angle bending roll 4" x 4" x 3/8" angle bending capacity specifications: driven shaft ...................... 120 mm diameter 400 mm length tooling dims ............... 450 mm od x 180 mm wide idler shafts .....

                    No price
                    Ronkonkoma, NY, USA
                  • CT Power Bending Roll #721

                    • Manufacturer: Cole-Tuve

                      New ct power bending roll model rm-4-86 49.2" bending length 3.38" roll diameter 10 fpm rolling speed approx electric: 2 hp, 220/440 volt, 3 phase rolls grooved for 3 sizes round bar: 3/8", 1/2", 5/8" scale to in...

                      No price
                      Ronkonkoma, NY, USA
                    • 16 GA x 36" Niagara Initial Pinch Power Bending Roll

                      • Manufacturer: Niagara

                        16 ga capacity mild steel 36" roll length 3" diameter rolls manual adjustment manual drop end forward/reverse runs well inspect under power in our branchburg nj warehouse

                        $2,950 (USD)
                        Livingston, NJ, USA
                      • 2013 .866" x 10' MG Model MH322D 4 Roll Double Pinch Hyd Plate Bending Roll

                            top roll: 350 mm / 13.8" | side rolls: 250 mm / 9.8" | bottom roll: 330 mm / 13" | equipped with: movable console, hydraulic system for opening the machine and removing the tube | width of plate: 3000 mm / 122"...

                            No price
                            Elk Grove Village, IL, USA