• Bernardo CS-350 14" Cold Saw - 2HP 220V 3 phase with coolant pump - MINT UNUSED UNIT

    • Manufacturer: BERNARDO

      bernardo cs-350 14" cold saw - 2hp 220v 3 phase with coolant pump - mint unused unit

      No price
      Hamilton, Canada
    • 1980 42" Chuck 75HP Spindle Mattison 24-42 ROTARY SURFACE GRINDER, AUTO CYCLE, MARPOSS GAGE, DRY BASE EXT. COOLANT,

      • Manufacturer: Mattison
      • Model: 24-42
      • Weight: 22,000 LBS

      42" mattison model no. 24 rotary surface grinder (this machine was made in the usa) ** automatic cycle with marposs in-process gaging system ** serial no.: 24-704 age: 1980 catalog specifications: magnetic chuck ...

      No price
      Harrison, NJ, USA
    • 2004 1.5" Dia. Cap 7.5hp Motor HP Royal Master TG12X4 CENTERLESS GRINDER, HYD. DRESSERS, WORKREST, COOLANT, ACCESSORIES

      • Manufacturer: Royal Master
      • Weight: 2,300 LBS

      royal master model tg12x4 centerless grinder model: tg12x4 s/n: 2680 new: 2004 capacity: infeed and thrufeed ....................... 0.004" to 1.5" dia. length .................................... 12' on 0.5" dia...

      No price
      Harrison, NJ, USA
    • 2014 Magnum 186 KW Generator & Power Unit

      • Manufacturer: Magnum
      • Hours: 3184.9

      magnum 186kw generator equipped as per below: - pintle hitch - tandem axle trailer - electric brakes - battery disconnect - in line engine block heater - 60/40 coolant - crank case ventalation canister heater - b...

      $69,500 (USD)
      Fargo, ND, USA
    • CROSS 55 GEAR TOOTH CHAMFERING MACHINE

        • Capacity: 15 Gal.
        • Weight: 3,700 lbs

        equipped with: draw rod collett stock divider hydraulic unit lube system air gun coolant guards change gears for one job 23/3/60 electrics catalog specifications: maximum gear diameter: 18" maximum face width...

        No price
        Warren, MI, USA
      • 1960 Cleerman ADT Twin Spindle AD234

        • Manufacturer: Cleerman

          tefc spindle motor, standard plain or 24" x 60" hydraulic shuttle table roller with programmable automatic cycles, ettco multi-drill units on each spindle, 4 spindles per head, new a-b magnetics and plc installed...

          No price
          Washington, PA, USA
        • 1995 HEM H130HM

          • Manufacturer: HEM

            you are viewing a used hem h130hm with crank adjusted guide arms, a chip auger, 0-100 in .min feed rate, and a cutting capacity (rectangular / round) of 20”w x 10”h16”h x 16”w this unit goes through our own un...

            No price
            Livonia, MI, USA
          • 2015 Tsugami BO 326-II 5871

            • Manufacturer: Tsugami

              c-axis: yes | y-axis: yes | chuck type: collet | bar capacity: 1.250 | single turret: yes | spindle motor: 7.5 | spindle speed: 8,000 | rapid traverse: 1259.84 | turret options: gang tool post (turning): 7 gang ...

              No price
              Maitland, FL, USA
            • 2002 GMC Savanna 3500 Van F29275

              • Manufacturer: GMC

                2002 gmc savanna 3500 van. approximately 257,600 miles. vin: 1gthg35r821207207. additional notes: this unit had a jasper reman engine about 4 years ago. the rear transmission seal leaks. the steering box is leak...

                No price
                McKees Rocks, PA, USA
              • 2012 Mazak Slant Turn Nexus 500M-2000U 5872

                • Manufacturer: Mazak
                • Spindle Bore: 7.280
                • Spindle Nose: A2-15

                c-axis: yes | x-travel: 18.31 | z-travel: 85.24 | chuck size: 18.00 | chuck type: air | bar capacity: 7.240 | spindle bore: 7.280 | spindle nose: a2-15 | spindle motor: 60 | spindle speed: 1,600 | tool positions...

                No price
                Maitland, FL, USA

              Have 5 seconds to help us improve the results?

              I'll do it
              No thanks