• 6" COSTELLO TUBE/PIPE BENDER

    No price - Helena, AL, USA

      specifications: the die on the machine & the extra one in the box are about 2". the bar on the machine is about 2". the circle disc are approximately 1", 1.5", 2.5" & 4.5". *see attached warranty...

    • 2000 Hines Bending Systems 200NC 23464

      No price - Melville, NY, USA
      • Manufacturer: Hines Bending Systems
      • Capacity: 3" O D x .125" Wall
      • Weight: 7,000 Lbs

      pro-face america touch screen plc controller hydraulic mandrel extractor overhead tie bar pressure die holder wiper die holder 15 hp main motor pressure die assist electric foot switch misc. dies i...

    • 2000 Hines Bending Systems 600NC 23581

      No price - Melville, NY, USA
      • Manufacturer: Hines Bending Systems
      • Capacity: 6" O D x .250" Wall
      • Weight: 18,000 Lbs

      pro-face america touch screen plc controller hydraulic mandrel extractor overhead tie bar pressure die holder 30 hp main motor (1) set 5" dies inspect under power in our philadelphia pa warehouse

    • 1996 Roundo R-13S Angle Bending Rolls

      No price - Venetia, PA, USA
      • Manufacturer: Roundo

      reduced price this machine has several hundred thousand dollars in tooling. machine is in good condition and running. tooling listed at the bottom of this quote. additional tooling has been mad...

    • 1967 3-1/2" Pines No. 2, Horiz., Mandrel Extractor, CW Rotation

      No price - Chicago, IL, USA
      • Manufacturer: Pines

      (1) used 3-1/2” pines mandrel-type horizontal tube bender, model no. 2, s/n 11255-67019, new 1967 wall wall counter-clockwise rotation oil reservoir in bed hydraulic mandrel extr...

    • 2″ PINES 20T HYDRAULIC VERTICAL TUBE BENDER

      No price - Bannockburn, IL, USA
      • Manufacturer: Pines

      2″ pines model 20t hydraulic vertical tube bender new 1963 motor driven with 20 hp, 3-phase, 60 cycle, ac motor and controls

    • 1-1/4" STEINWEG, #B32, 1.8/2.8 HP, 1975

      No price - Hialeah, FL, USA
      • Manufacturer: Steinweg

      specifications: single bends (65,000 psi)--1 bar 1-1/4" --2 bars 15/16" --3 bars 3/4" --4 bars 11/16" --5 bars 9/16" (92,000 psi)--1 bar 1-1/8" --2 bars 7/8" --3 bars 11/16" --4 bars 5/8" --5 bars ...

    • SMS SMS 200 LH #16088A

      No price - Monclova, OH, USA
      • Manufacturer: SMS

      model #:  sms 200 lh serial #:  200-98002 2″ maximum capacity 180 degree maximum left hand rotation mandrel extractor programmable control a bend controller 120″ maximum tube length (estimated) pre...

    • 1973 PINES MODEL 1400 ROTARY TUBE BENDER 15307

      No price - Des Plaines, IL, USA
      • Manufacturer: Pines

      age? stainless steel tubing y.p. to 60,000 psi 7/8" od x .065" wall counterclockwise rotation mandrel extractor degree of bend selector automatic lubrication temporary specifications

    • 1976 PINES MODEL 3/4 HYDRAULIC ROTARY TUBE BENDER 15637

      No price - Des Plaines, IL, USA
      • Manufacturer: Pines

      hydraulic mandrel extractor with mandrel rods clamp and pressure die holders 10 position degree of bend selector a.c. main drive motor and complete electrical controls pedestal mounted 9 position p...