Top Seller
no-image_en.png
Location:
Hialeah, FL
Manufacturer:
Metalmaq

Specifications

Condition:
used
Stock number:
4209
F.o.b:
Hialeah, FL
Division:
Metalworking
Electrics:
220/440 volt, 3 phase, 60 Hz.
Accessories:
$32,950.00
Air power drawbar:
650.00
Swivel base for 6" vise:
175.00
Ball screw on vertical (z) axis:
1,900.00
Kurt 6" angle-lock milling vise:
425.00
Subcategory:
Millers, vertical

Description

One new METALMAQ model B410VS-SP Bed Mill with standard
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . $32,950.00
OPTIONAL ACCESSORIES:
Ball screw on vertical (Z) axis . . . . . . . . . . . . . . . . . . 1,900.00
Air power drawbar . . . . . . . . . . . . . . . . . . . . . . . . . 650.00
11" x 58" table providing 47" longitudinal travel . . . . . . . . . 950.00
Extra high column (5.9" higher than standard column). . . . . . . . 750.00
NEWALL Topaz 2 axis digital readout (installed) . . . . . . . . . . 2,650.00
NEWALL Topaz 3 axis digital readout (installed) . . . . . . . . . . 3,250.00
KURT 6" angle-lock milling vise . . . . . . . . . . . . . . . . . . 425.00
Swivel base for 6" vise . . . . . . . . . . . . . . . . . . . . . . 175.00
ELECTRICS: 220/440 volt, 3 phase, 60 Hz.
F.O.B.: Hialeah, FL
STANDARD ACCESSORIES:
5 HP variable speed head with #40 spindle taper
Hardened and ground 15" x 50" table with ground T-slots
Hardened and ground longitudinal (X), cross (Y) and vertical (Z) axes ways
Ball screws on longitudinal (X) and cross (Y) axes
Automatic longitudinal (X), cross (Y) and vertical (Z) feed
and rapid travese via AC servo motors
Box ways on both cross (Y) and vertical (Z) axes
Turcite-B coated XYZ ways, gibs and saddle slideways
Counter-weight on head
Licensed Meehanite casting
Electric box and control panel
Coolant system with base tray and column splash guard
Automatic lubrication
Quartz worklight
SPECIFICATIONS:
Size of table (length x width)
--standard 15" x 50" (380mm x 1270mm)
--optional 15" x 58" (380mm x 1470mm)
Longitudinal travel--50" table 39.3" (1000mm)
--58" table 47" (1200mm)
Cross travel 20" (500mm)
Vertical head travel
--standard column 19" (480mm)
--optional exteded column 24.8" (630mm)
Quill traverse 5" (127mm)
Quill power feed rate--number 3
--range .0015"--.003"--.006"
(0.4mm--0.8mm--0.14mm)
Spindle taper #40
Main motor 5 HP
Head moves right to left 45 degrees
Automatic power feed rate XYZ axes 1 to 47ipm (25mm a 1200mm)
Rapid traverse rate XYZ axes 78.7 ipm (2000mm/min)
Distance from center of spindle
to the column 19.3" (490mm)
Distance from spindle nose to table top
--standard (min-max) 5.5"--23.6" (140mm--600mm)
--with optional high column 5.5"--29" (140mm--740mm)
Spindle speeds--number infinitely variable
--range 50 to 3600 rpm
Net weight (approx.) 6,750 lbs. (3100 kgs)