2008 Pressen des Herstellers A.KAHL
Location:
Pähl, Germany

Specifications

Condition:
used
Year:
2008
Subcategory 2:
Pelletizing presses
Subcategory 3:
PELLET-production complete
Condition info:
Used machine Ready for use
Subcategory:
Presses

Description

-Hydraulic unit for feeding fuel ( 2011 )
- Feeding container for fuel, 4 m3. (2008)
- Own 6 MW, moving grate. (2008)
- Hydraulic unit for moving grate (2008)
- Primary air fan, blow air under the grate.(2008)
- Secondary air fan, blow air up to flames.(2008)
- Chain conveyor for take ash out of own.(2005)
- Mixer, mix hot and cold air
Feeding container for wet sawdust. ( 20 m³ )(2009)
- Feeder for wet sawdust with leveller
- Feeding screw for wet sawdust
- Drying drum, 3 levels, Swiss Combi MK 5. ( L= 12 m diam. 3,8 m)
- Airlock, take dry sawdust to chain conveyor
- Cyclone. Separate fine dust and air
- Airlock, take fine dust to chain conveyor
- Main fan, 90 kw
- Chain conveyor. 35 m. Take dried sawdust to storage.(2008)
- Chain conveyor. 6 m goes two ways, forward or back. (2006)
- Automatic water hydrant, for fire (2 ps) (2008)
- Heat sensors. (2 ps) (2008)
- Electrical center, with Siemens logistic. (2008)
- PC-computer for use dryer from control room. (2008)
Cameras, ( 4 ps ) same control panel than factory (2008)
Iveco generator (diesel) can give power to all dryer. (2004)
PELLETFACTORY
- 2 pcs hydraulic units. (2006 and other 2008)
- Feeding table whit scrapers (4000 mm * 12000 mm) Table is whit 600 mm legs
- 4 pcs scrapers with cylinders take dry sawdust out of table to feeding screw
- 2 pcs feeding screws ( diameter 600 mm ja lenght 6000 mm ) take sawdust to hammermill
- 2 pcs Wynween (HM hammermill with 132 kW motor. (2006 and other 2008)
- 2 pcs Stone pocket, take stones and heavy particles out of sawdust
- 2 pcs Pneumatic movers for hammermill. (2008 and other 2008)
o 2 Pcs Fan with 11 kW motor
o 2 pcs Filter station
o 3 pcs Airlock with 1,5 kW motor
- 3 pcs Feeder with level controller and with leveler. (two of them 2006 and one 2008)
2 * 2,2 kW and 2 * 1,5 kW motors and coolers for motor. Speed of leveler control intake power of main motor of press by automatic
- 3 pcs Mixer, that homogenized chips for press 3 * 11 kW motor. and turnig plates
- 3 pcs. Pellet presses Kahl C – kW motor and machine beds
- 3 pcs Oil coolers cooling gearbox oils for pellet press. 3 * 2,2 kW
- 3 pcs Central lubrication units for greasing the collerheads
- 5 pcs chain conveyors take hot pellets from press to cooler. 2 * 1,5 kW motor and 3 * 2,2 kW motor
- 1 pcs Horisontal Beltcooler, for cooling hot pellet for storage. 2,2 kW motor. (2006)
1 pcs Cooling system. (2008) 18,5 kW motor cyclone, Airlock 2,2 kW
- 1 pc Belt conveyor, to take cooled pellet to screen. 0,50 kW motor
- 1 pc Screen, to take fine dust out of pellet. Fine dust goes back to feeding table by air. 0,55 kW motor
- 1 pc Belt conveyor, to take pellet from screen to storage
- 1 pc Dust evacuation system
- Fan 30 kW motor
- Cyclone
- Airlock 2,2 kW motor
- 1 pc Air compressor with dryer
- 1 pc Air compressor
- 1 pc Electric container. (2,4 * 12 m)
- Soft starters for Presses and big fans and hammermills
- Control system by Moeller
- Belt conveyor for taking pellet to silo
- Silo, w