Top Seller
SHARP LMV / LMV-50 9"
Location:
Port Orange, FL
Model:
LMV / LMV-50

Specifications

Condition:
new
Stock number:
LMV
Table:
Working surface 9” x 42" 9” x 50"
Taper:
R-8
Models:
LMV LMV-50
Spindle:
Motor 3 HP
Capacity:
Table travel; x-axis 30" 37"
Warranty:
1 YEAR
Net weight:
2,400 lbs.
Ram travel:
12"
Head swivel:
360°
Knee travel:
16"
Wiring voltage:
220/440v, 3 phase, 60 Hz
Quill feed (ipr):
0.0015”, 0.003”, 0.006"
Speed (vari-speed):
60-4,500 RPM
Dimensions & weight:
Floor area (w x d) 7’ x 6.5'
T-slot number, size:
3, 5/8"
Quill travel (z-axis):
5"
Saddle travel; y-axis:
12"
Spindle to nose table:
2 1/8” - 18"
Spindle to column (min-max):
6 3/4" - 18 1/2"
Head tilt up-and-down (each way):
45°
Head tilt; right-to-left (each way):
45°
Subcategory:
Mills
Subcategory 2:
Vertical knee type

Description

ITEM: 9" x 42" - 50" Vertical Knee Milling Machines
MAKE: SHARP®
MODEL: LMV / LMV-50
Product Features
Head
To dissipate heat in the 3 HP motor driven head, a pair of high output fans is installed. This allows the machine to work demanding jobs for extended periods without damaging the motor, belts and bearings. A unique SHARP feature
The motor shaft and Vari Drive pulleys are dynamically balanced, then hard-chromed this allow a vibration free milling even at high speed
Since the Vari-speed drive system is operated by sliding the Vari Drive pulley up and down the motor shaft. The motor shaft is therefore chrome-plated, and has an oil channel that is fed by a grease fitting on the lower end for self-lubricating purpose. This ensures the sliding motion is trouble free at all times. A unique SHARP feature
The motor shaft that drives the pulley and the spindle is subject to a lot of lateral stress. A roller bearing is installed for the lower support of the motor shaft. A unique SHARP feature
Beside swiveling 90 degree side to side, the head can also swivel up and down by virtue of a knuckle joint design. The new design developed by Sharp uses 6 bolts, 3 each side, that fitted into a circular T-slot milled at the inside of the over arm and secured by nuts from the outside. It secured the head tightly and offered high accuracy in milling operations
A matched pair of super-precision ABEC-7 angular contact bearings supports the spindle. The quill is CNC-ground to a mirror finish, and then chromed to fit the housing. Together, they insure spindle run out of no more than 0.00002” TIR- the best in the industry
DVS (Digital Variable Speed) Head available
High reliability with fewer moving parts than regular vari speed head
Dynamic brake
Low voltage control
Large Digital rpm display
Fully enclosed display unit
Dependable Inverter Drive System
Machine can run on single phase or 3 phase electricity
Safety device prevents machine from self starting after power failure or after emergency stop being pushed
Column, Table and Knee
Certified MEEHANITE castings are used for superior rigidity and better dampening of vibrations
Table and saddle backlash is controlled by a double-nut design that keeps the feed screw in contact with a pair of bronze nut at all times. A unique SHARP feature
The end of the table and saddle are mounted with thrust bearings that pre-load the feed screw, eliminating endplay for precisely controlled lateral movement
The end of the table and saddle are mounted with thrust bearings that pre-load the feed screw, eliminating endplay for precisely controlled lateral movement
nstead of hand scraping the top of the knee ways for oil retention, the matching underside of the saddle is hand-scraped. This extra step avoids having chips and dirt embedded in the knee ways and damages the sliding area
STANDARD EQUIPMENT
Hard-chromed ways
One-shot lube system
Front and rear rubber way covers
Tool kit
Options/Accessories
CALL FOR PRICE
Digital Variable Speed (D