Top Seller
PROMACO RBM 2-30 UNIVERSAL (SEE
Location:
McClellan Park, CA
Manufacturer:
PROMACO
Model:
RBM 2-30

Specifications

Condition:
new
Stock number:
870
Depth:
22 Inches
Width:
26 Inches
C, legout:
2" X 1" X 3/16" 12" Standard
Round bar:
1-1/4" 24" Special
Net weight:
350 lbs
Rect. tube:
2" X 1" X 11 Gauge 48" Special
Round tube:
3/4" X 16 Gauge Tube 12" Special
Shaftspeed:
6.5RPM
Square bar:
1-1/8" 24" Standard
Tee, legin:
1.5" X 1.5" X 1/4" 20" Standard
Flats, easy:
3" X 5/8" 14" Standard
Flats, hard:
3/4" X 1/4" 14" Standard Rolls
Square tube:
1" X 1" X 11 Gauge 25" Standard
Tee, legout:
1.5" X 1.5" X 1/4" 12" Standard
Angle, legin:
1" X 1" X 1/4" 20" Standard
Pipe, sch 40:
1" Sched 40 Pipe 12" Special
Round tube 2:
2-3/8" X 16 ga Tube 48" Special
Square bar 2:
1/2" 3" Special
Angle, legout:
1" X 1" X 1/4" 17" Standard
Flats, easy 2:
5" X 3/8" 13" Special
Flats, hard 2:
2" X 3/8" 16" Standard
Flats, hard 3:
2-1/2" X 1/4" 30" Standard
Square tube 2:
1.5" X 1.5" X 11 ga. 40" Special
Angle, legin 2:
1.5" X 1.5" X 3/16" 21" Special
Overall height:
51 Inches
Pipe, sch 40 2:
1.5" Sched 40 Pipe 18" Special
Shaft diameter:
30MM
Angle, legout 2:
1.5" X 1.5" X 3/16" 16" Special
Approximate pass line:
40 Inches
Gross (shipping) weight:
500 lbs
Number of driven shafts:
2
Electric motor rating (0.75 kw):
1 HP
Power requirement 220 volt, 1 ph:
5.9 AMPS
Power requirement 220 volt, 3 ph:
3.7 AMPS
Power requirement 440 volt, 3 ph:
1.8 AMPS
Subcategory:
Benders
Subcategory 2:
Angle rolls

Description

Model: PROMACO RBM-230
MATERIAL: DIMENSIONS: MIN. I.D.: REQUIRED TOOLING:
Flats, Hard: 3/4" X 1/4" 14" Standard Rolls
Flats, Hard: 2" X 3/8" 16" Standard
Flats, Hard: 2-1/2" X 1/4" 30" Standard
Flats, Easy: 3" X 5/8" 14" Standard
Flats, Easy: 5" X 3/8" 13" Special
Square Bar: 1-1/8" 24" Standard
Square Bar: 1/2" 3" Special
Angle, Legout: 1" X 1" X 1/4" 17" Standard
Angle, Legout: 1.5" X 1.5" X 3/16" 16" Special
Angle, Legin: 1" X 1" X 1/4" 20" Standard
Angle, Legin: 1.5" X 1.5" X 3/16" 21" Special
Tee, Legout: 1.5" X 1.5" X 1/4" 12" Standard
Tee, Legin: 1.5" X 1.5" X 1/4" 20" Standard
C, Legout: 2" X 1" X 3/16" 12" Standard
Round Bar: 1-1/4" 24" Special
Pipe, SCH 40: 1" Sched 40 Pipe 12" Special
Pipe, SCH 40: 1.5" Sched 40 Pipe 18" Special
Round Tube: 3/4" X 16 Gauge Tube 12" Special
Round Tube: 2-3/8" X 16 ga Tube 48" Special
Square Tube: 1" X 1" X 11 Gauge 25" Standard
Square Tube: 1.5" X 1.5" X 11 ga. 40" Special
Rect. Tube: 2" X 1" X 11 Gauge 48" Special
SPECIFICATIONS:
Electric Motor Rating (0.75 KW): 1 HP
Power Requirement 220 Volt, 3 PH: 3.7 AMPS
Power Requirement 440 Volt, 3 PH: 1.8 AMPS
Power Requirement 220 Volt, 1 PH: 5.9 AMPS
Shaft Diameter: 30MM
Shaftspeed: 6.5RPM
Number of Driven Shafts: 2
Number of Adjustable (Or Form) Rolls: 1
Width: 26 Inches
Depth: 22 Inches
Overall Height: 51 Inches
Approximate Pass Line: 40 Inches
Net Weight: 350 lbs.
Gross (Shipping) Weight: 500 lbs.
FEATURES:
* Rugged Steel Frame.
* Bi-Directional Drive Motor 220 Volt, 3 PH -10:1 Gear
Reduction Unit, Operating in Constant Oil
Bath.
* High Strength Steel Shafts, Powered By A Spur Gear Drive.
* Forming Roll Guide Block Traveling on Hardened Slide Ways.
* Roll Shafts Journaled Tapered Roller Bearings, Greased &
Sealed For Life
* Two Adjustment Scales For The Depth Adjustment of The
Forming Roll.
* Two Laterally Mounted, Adjustable Guide Rollers.
* Main Power on/off Switch and Three Position Selector
Switch For Directional Control of The Electric Motor.
* Set of Shims For clearance Adjustment of The Standard
Rolls.
* 18 Piece Standard Roll Set is Included.
* Machine STand Is Included, With Generous Tooling Storage
Space.
The RBM 2-30 is suitable for rolling a wide variety of
materials, including structural and stainless steels, as
well as, copper, aluminum and brass.
The machine is furnished with a standard or "Universal" Roll
set, consisting of eighteen roll discs. Each of the
machine's three shafts is equipped with two large discs and
four smaller spacer discs, of varying thickness (18 Pieces
in all). This system allows the machine operator to
"Construct" the dies that are required to roll many shapes
and sizes of materials, according to the sequence in which
the discs are installed on the roll shafts. Therefore, the
need for special tooling is eliminated on rolling
applications such as, flat bar, square bar, channels, tees,
box tubing and most angles. Round mechanical tubing and
schedule 40 pipe may also be rolled, however, these
applications require optional