Top Seller
KENT KTM-3VKF MANUAL MILL W/FREQ.DRIVE
Location:
McClellan Park, CA
Model:
KTM-3VKF
Spindle Taper:
R8 (NMTB-30 AVAILABLE)

Specifications

Condition:
new
Stock number:
2211
Hp:
this is ideal where only single-phase power is
Ram travel:
20"
Table size:
10" X 50"
Quill travel:
5"
Spindle motor:
3 HP (1750 RPM @ 60 HZ)
Spindle speed:
Variable 60-500-4200 (2 RANGE, HI/LOW)
Spindle taper:
R8 (NMTB-30 AVAILABLE)
Quill diameter:
3.375"
Boring capacity:
6.0" Diameter
Quill feed rate:
0.0015/0.003/0.006" PER REV
Skid dimensions:
72" X 72" X 84"H (Skid)
Milling capacity:
2.0 IN3/MIN
Power requirements:
220/440 VOLTS, 3 PH, 60 HZ, 10/5 AMP
Knee travel (z-axis):
16"
Table travel (x-axis):
36"
Saddle travel (y-axis):
15.75"
Machine weight (approx):
3250 lbs
Max. work load (center):
850 lbs
Drilling capacity (power):
0.37" Diameter
Drilling capacity (manual):
0.75" Diameter
Frequency drive milling head. note:
The AC-Frequency drive
Subcategory:
Vertical mill
Subcategory 2:
Milling machines

Description

Model: KTM-3VKH
Table Size: 10" X 50"
Table Travel (X-Axis): 36"
Saddle Travel (Y-Axis): 15.75"
Knee Travel (Z-Axis): 16"
Quill Travel: 5"
Ram Travel: 20"
Spindle Motor: 3 HP (1750 RPM @ 60 HZ)
Power Requirements: 220/440 VOLTS, 3 PH, 60 HZ, 10/5 AMP
Spindle Speed: Variable 60-500-4200 (2 RANGE, HI/LOW)
Spindle Taper: R8 (NMTB-30 AVAILABLE)
Quill Diameter: 3.375"
Quill Feed Rate: 0.0015/0.003/0.006" PER REV
Drilling Capacity (Manual): 0.75" Diameter
Drilling Capacity (Power): 0.37" Diameter
Boring Capacity: 6.0" Diameter
Milling Capacity: 2.0 IN3/MIN
Max. Work Load (Center): 850 lbs.
Machine Weight (Approx): 3250 lbs.
Skid Dimensions: 72" X 72" X 84"H (Skid)
FEATURES:
* 3HP spindle motor wiht electronic variable speed (EVS) AC-
frequency drive milling head. NOTE: The AC-Frequency drive
can accept single phase power at 50% reduction in output of
HP....this is ideal where only single-phase power is
available. * Table, Saddle, and Knee Hardened & Ground
Dovetail Ways
* Precision ground leadscrews with backlash compensating
double nut
* Precision bored and ground miling head, with super
precision ABEC-7 bearings
* Meehanite castings, with built-in coolant reservoir in
machine base
* Centralized one-shot lubrication, with metered check-
valves
OPTIONAL ACCESSORIES:
ACU-RITE 200M DRO System (2-axis, 0.0002"
resolution)
Table Power Feed (X-AXIS)
Saddle Power Feed (Y-AXIS)
Knee Power Feed (Z-AXIS) $600.00 Air Power
Drawbar (Maxi-torque, USA Made)
Flood Coolant System (Internal Built-In)
Flood Coolant System (External Tank)
Prolong Ultra-Cut Coolant (2.5 Gallons)
Riser Block (4")
Riser Block (6")
Riser Block (8")
Angle-Lock Vise (6")
Angle-Lock Vise (8")
Rotary Table (12", Vertical & Horizontal)
Clamping Kit
R8 Collet Set (11 PC., 1/8" TO 3/4")
DRO Installatoin charge