• Dia In Inches By Length In Feet Ball Mill #13586

        32" dia x 42" long cs jkt wet ball mill. full cs jkt. with 7 1/2 hp, 3/60 motor. triple chain drive. has 8" x 42" feed/discharge, 4" access port w/cover on end of shell. mtd on pillow block bearings. rotary joint...

        No price
        West Windsor Township, NJ, USA
      • Dia In Inches By Length In Feet Patterson Pebble Mill #11562

            6' x 9' patterson jkt pebble mill. nb #873. jkt rated 15 psi. fully jkt including both ends. dished ends. lined with belgium block lining. driven by bull gear on one end of mill. 18" charge port, 3" discharge. no...

            No price
            West Windsor Township, NJ, USA
          • BEKAERT 10 BLOCK WIRE DRAWER LINE W/PAYOFF & SPOOLER

            • Manufacturer: Holder

              equipped with: payoff and spooler plc: remote plc | type: conical reel ws2000 | motors: ind. ac motor w/frequency control on each block | cooling: internal water cooled capstans and dies | controls: touch panel p...

              No price
              Ivyland, PA, USA
            • BEKAERT 10 BLOCK WIRE DRAWER LINE W/PAYOFF & SPOOLER

              • Manufacturer: Holder

                equipped with: payoff and spooler plc: remote plc | type: conical reel ws2000 | motors: ind. ac motor w/frequency control on each block | cooling: internal water cooled capstans and dies | controls: touch panel p...

                No price
                Ivyland, PA, USA
              • Thomas Conveyor 9 X 34

                • Manufacturer: Thomas

                  twin 9" x 34" screw feeders, stainless steel: motor specifications; 15 hp, 1700 rpm, 230/460 volt, 4.7/2.4 amps, 60 hz, 1.00 s.f. continuous duty. speed reduction unit input speed 1700 rpm, output speed 45 rpm ...

                  $3,000 (USD)
                  Millwood, WV, USA
                • metallic systems 58 sq ft. Horizontal impervite shell + tube. Impervite heat exchanger carbon steel shell rated 100 psi @ 340 F. Impervite tubes rated 100psi @ 340F. National Board #1800 Serial # 8115, built 1998. 12" Dia x 77 1/2" long. 2" servi...

                  • Manufacturer: National

                    metallic systems 58 sq ft. horizontal impervite shell + tube. impervite heat exchanger carbon steel shell rated 100 psi @ 340 f. impervite tubes rated 100psi @ 340f. national board #1800 serial # 8115, built 199...

                    No price
                    Greensboro, NC, USA
                  • 60" FENN MODEL VNC-60-12 VERTICAL SPINNER BLOCK

                    • Manufacturer: Spinner

                      60" block dia with shedding ring tube cap.: 1/4" to 1.310" o.d designed for 60" dia. 500# coil material: hard copper drum speed: 3600 sfm max pull at die box @ 100% of drive, motor cap. @ 400rpm 12,500# drive m...

                      No price
                      Newark, NJ, USA
                    • 84", MANNESMANN DEMAG, No. 80TVC 2000, 1996, SPINNER BLOCK

                      • Manufacturer: Demag

                        machine# 10345 specifications : 1. make : mannesmann demag meer (sms-meer, germany) 2. year of manufacturer : 1996 (m/c no.: 0204025-00.000) 3. type : 80tvc ...

                        No price
                        North Branford, CT, USA
                      • 2009 J DEERE 700JLGPT8821

                        • Manufacturer: John Deere
                        • Hours: 3586

                        hours: 3586 rops:o pads:24 in. midwestern sideboom:m540c line winch:two speed hyd. planetary boom winch:single speed hyd. planetary integrated draw works:with fairlead frame extendable counterweight:with four bar...

                        $169,000 (USD)
                        Verona, KY, USA
                      • 24", MARSHALL RICHARDS, Pull 2000 Lb. INVERTED, 2000 FPM, 7/16" DIA INPUT

                        • Manufacturer: Marshall

                          machine # 8063 manufacturer: marshall richards machine ltd. (u.k.) type: vertical continuous spinner type tube drawing block capacity: maximum entry size (copper tube): 7/16" (11mm) o.d. minimum exit finish siz...

                          No price
                          North Branford, CT, USA

                        Have 5 seconds to help us improve the results?

                        I'll do it
                        No thanks