Used Extruders

WAYNE 1.250″ 30:1 L/D EXTRUDER 16355

• Manufacturer: Wayne

Wayne 1.25″ extruder, S/N 9414-832. 30:1 L/D electrically heated, air cooled, vented (venting is plugged), barrel driven by a 7.5HP DC motor with SCR control 230-Volts input power. Includes track wheel base and a...

GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18364

One (1) Used Gloucester model 35250R2 3.5” 32:1 L/D extruder. S/N 36736/11. Having an electrically heated, air cooled, and non-vented barrel at approximately a 65” center line height. Barrel is set up for Contra-...

GLOUCESTER 2.5″ 32:1 L/D EXTRUDER 18366

One (1) Used Gloucester model 25225R2 2.5″ 32:1 extruder having an electrically heated, air cooled, and non-vented barrel at approximately a 65″ center line height. S/N 36736/25. Barrel is set up for Contra-Cool ...

HPM 3.5″ 30:1 L/D EXTRUDER 17578

One (1) used 3.5″30:1 HPM extruder having an electrically heated water cooled (closed loop) vented and plugged barrel at a 51 ½” centerline height. Koellmann gearbox is driven by a 100 HP D/C motor with a Eurothe...

WELEX 2″ 24:1 L/D CO-EXTRUDER 17576

• Manufacturer: Welex

One (1) used 2″ 24:1 L/D Welex co-extruder. Water cooled. Missing motor, drive panel, and pedestal. Last used on a sheet line.

DAVIS STANDARD 15INDS20 1.5″ EXTRUDER 12754

• Manufacturer: Davis-Standard

Davis standard model 15INDS20 1.5″ extruder S/N K-9754. SO# 02359. 24:1 L/D. Powered by a fan cooled 15 HP 500-Volt 1750/2300 RPM DC motor through a 6.53:1 gearbox 152 RPM screw speed. Electrically heated and fan...

GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18365

One (1) Used Gloucester model 35250R2 3.5″ 32:1 extruder having an electrically heated, air cooled, vented, and plugged barrel at approximately a 65″ center line height. S/N 36736/12. Barrel is set up for Contra-...

PRODEX 4.5″ 32:1 L/D EXTRUDER 18180

One (1) used Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear type gearbox and is direct driven in a tuck under ...

GLOUCESTER 2.5″ 32:1 L/D EXTRUDER 17690

Gloucester 2.5″ extruder, 32:1 L/D five (5) zone air cooled and vented barrel at a 45″ centerline height. Top center feed throat. Driven by a 50 HP A/C 1750/2100 RPM motor, includes 6 zone temperature control pan...

DAVIS STANDARD 165MM60TPIH 6.5″ EXTRUDER 10869

• Manufacturer: Davis-Standard

Davis Standard model 165MM60TPIH, S/N X7206 27:1 L/D 150HP DC motor 100RPM screw speed 526HP rated gearbox with a 1.5 service factor. No feed throat, no control panel. Water cooled barrel. Last used as a secondar...

ACTUAL AE-25/10/22 25MM PEDESTAL EXTRUDER 18705

One (1) used Actual model AE-25/10/22 25mm pedestal extruder. Having a 24:1 L/D ratio. Unit has a three (3) zone electrically heated, air cooled, non-vented barrel. Barrel can be raised or lowered and also tilts ...