New Machine Tools in Tuscany, Italy

C.L.O.M.E.A. PICM

• Manufacturer: C.L.O.M.E.A.

PICM Software and Hardware with manual input of the bar-feeding speed, to allow the execution of very short radii and to work on short arcs. Software and Hardware for the management of the automatic bar-reading e...

C.L.O.M.E.A. PIA

• Manufacturer: C.L.O.M.E.A.

PIA Software and Hardware for the automatic management of the bar-feeding speed calculation, to allow the execution of very short radii and to easily work on short arcs.

C.L.O.M.E.A. CR40

• Manufacturer: C.L.O.M.E.A.

High performance hydraulic bending machine for metal and plastic profiles. Machine body in cast iron, gears in hardened steel and three steel driving shafts, mounted on conical bearings and controlled by a gearmo...

C.L.O.M.E.A. CR120

• Manufacturer: C.L.O.M.E.A.

High performance hydraulic bending machine for metal and plastic profiles. Machine body in cast iron, gears in hardened steel and three ground tempered steel driving shafts, mounted on conical bearings and contro...

C.L.O.M.E.A. CRM35

• Manufacturer: C.L.O.M.E.A.

High performance hydraulic bending machine for metal profiles. Machine body in cast iron, gears in hardened steel and three steel driving shafts mounted on conical bearings and controlled by a gearmotor. The mach...

Draw Bench - short version

• Manufacturer: GIUSEPPE MEALLI

Draw Bench, short version - Usefull length: 850 mm. Supplied without draw tongs, available as accessory. Two drawing speeds: direct drive or 4:1 gear ratio. Maximum wire diameter: 6 mm. Made in Italy. Drawbench ...

Draw Bench - Usefull length: 130 cm

• Manufacturer: GIUSEPPE MEALLI

Supplied without draw tongs, available as accessory. The gears rotate on self-lubricating bushes; the chain also, unlike other benches, is supported by strips in antiwear material. Made in Italy. Drawbench with s...

Manual Rolling Mill plate mm 120

Manual Rolling Mill mm 120 Manual Rolling Mill plate mm 120 with reduction gearbox One piece cast iron construction for maximum strength and rigidity. This mill are entirely made in Italy, which translates into g...

Manual Rolling Mill wire mm 100

Manual Rolling Mill mm 100 Manual Rolling Mill wire mm 100 with engraved side rollers New series of manual rolling mills realized with steel structure. The rollers rotate on long lasting sintered bearings impregn...

Manual Rolling Mill plate mm 100

Manual Rolling Mill mm 100 Manual Rolling Mill plate mm 100 with reduction gearbox New series of manual rolling mills realized with steel structure. The rollers rotate on long lasting sintered bearings impregnate...

Manual Rolling Mill plate and wire mm 120

Manual Rolling Mill mm 120 Manual Rolling Mill plate and wire mm 120 with reduction gearbox One piece cast iron construction for maximum strength and rigidity. This mill are entirely made in Italy, which translat...

Manual Rolling Mill plate and wire mm 100

Manual Rolling Mill plate and wire mm 100 with reduction gearbox New series of manual rolling mills realized with steel structure. The rollers rotate on long lasting sintered bearings impregnated with lubricant o...

Manual Rolling Mill plate and wire mm 120

Manual Rolling Mill mm 120 Manual Rolling Mill plate and wire mm 120 with reduction gearbox New series of manual rolling mills realized with steel structure. The rollers rotate on long lasting sintered bearings i...

C.L.O.M.E.A. CN11

• Manufacturer: C.L.O.M.E.A.

CN11 Numerical control with Linux operating system for multiple-run machining up to 3 radii. Single bar-feed speed, automatic management of the fitting sections and bar check. Network connection and remote assist...

C.L.O.M.E.A. CN07

• Manufacturer: C.L.O.M.E.A.

CN07 Control console to manage machining by means of a programmable positioner.