Building Filters
CME 75 AUGER DRILL RIG #10187T
Cummins diesel engine, auto hammer, breakout wrench, mounted on International 4900 DT466E truck with Detroit diesel engine, no water pump but hydraulically plumbed for water pump Price: $62,500
CME 55 AUGER DRILL RIG #12922T
Manufactured 1968, 3L8 Moyno mud pump, hydraulic rod holder and breakout wrench, CME auto hammer, 2 winches, multi-fuel carrier engine/diesel deck engine, mounted on 1971 American General M35A2 2.5 ton all wheel ...
1986 CME 55 AUGER DRILL RIG #8070Ta
Manufactured 1986, mounted on 2008 Freightliner M2 4x3 truck with approx 141,000 miles, in/out slide base, Moyno 3L6 pump, cathead, 140/300# auto hammer, 28’ long derrick, 3200# winch, Ford 300 ci deck engine, 75...
1998 CME 550X DRILL RIG #1283Tb
Manufactured 1998, Drill completely rebuilt 2025 with everything new on the drill side brand new, 1 wireline winch, 1 main winch, 1 worker winch, auto hammer, Cummins diesel engine, 3L8 Moyno pump, CME breakout t...
1995 CME 550X DRILL RIG #10923T
Manufactured 1995, Cummins 3.8L diesel engine, two lifting winches, water tank and pump, recently rebuilt (rear) drill transmission and overload clutch, 75’ hollow stem auger flights and 70’ drill rod, miscellane...
1979 CME 55 AUGER DRILL RIG #10416Tb
Manufactured 1979, Ford I-6 gas deck engine, auto SPT hammer, 3 winches, mounted on 2005 Ford F750 4 x 2 truck with 6L diesel engine, automatic transmission, non-CDL, approx 63,500 miles Price: $87,500
1969 CME 55 AUGER DRILL RIG #8357T
Manufactured 1969, gas deck engine, in/out and side to side slide base, cathead, no auto hammer, mounted on 1985 Ford F700 2WD truck with gas engine, manual transmission, no angle capability, no auto hammer, auge...
1996 CME 75 AUGER DRILL RIG #10416Ta
Manufactured 1996, Cummins 6 cylinder diesel deck engine, auto SPT, Moyno water pump, 2 winches (wireline), 150 gal water tank, mounted on 2005 International 7800 4 x 4 truck with diesel engine, manual transmissi...
2016 CME 55 AUGER DRILL RIG #10551Td
Manufactured 2016, 8000 hours, mounted on 1995 Morooka 1100 (6300 hours) Price: $250,000 USD CME 55HT
1989 CME 550 BUGGY DRILL RIG #4781Ta
Manufactured 1989, Cummins deck engine, in/out slide base, auto hammer, Moyno pump, (2) Pullmaster winches (PL5, PL2), 3200 lb gear winch, auger guard, water tank, no angle capability. Good condition, recently re...
1991 CME 45 AUGER DRILL RIG #10832T
Manufactured 1991, diesel deck engine, mounted on 991 Ford Superduty with diesel engine, in-out slide base, water truck, 3 winches, no angle capability, 2 rear hydraulic leveling jacks Price: $57,500
1980 CME 55 AUGER DRILL RIG #10556T
Manufactured 1980, Ford 6 cylinder engine (rebuilt – 0 hours), Moyno 3L6 pump rercently replaced, all hydraulic pumps rebuilt, feed table rebuilt 4 bearing, chain square drive. Auto hammer rebuilt, new hydraulic ...
1985 CME 55 AUGER DRILL RIG #3744T
Manufactured 1985, approx 2350 hours, Cummins 71hp engine, mounted on 2000 Ford F650 with diesel engine, approx 45,000 miles, (13) 5’ x 8” sections, (13) 5’ x 6” sections Price: $82,500
1985 CME 550 ATV DRILL RIG #10346T
Manufactured 1985, engine was replaced with a new engine in 2023, completely rewired, started replaced 2024, brakes were removed in preparation for replacement (new brake equipment not yet installed), clutch need...
1987 CME 55 AUGER DRILL RIG #3853Ta
Manufactured 1987, 6 cyl Ford gas engine on deck, mounted on 1987 Single axle International truck with diesel engine, Beam pump, drop hammer, cathead, rebuilt transmission and rear end, 60+' of 4-1/4" Acker auger...
