- Trusted Seller
4.5" Davis Standard Single Screw Ram Stuffing Extruder, Model 45IN45-34, 400HP, New in 2011
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard Single Screw Ram Stuffing Extruder, Model 45IN45-34, New in 2011 Pneumatic Ram Stuffer, Stuffer 28.5"" x 13.5" 400HP Direct Drive AC Motor, 1775 RPM, Yaskawa AC Drive Pro-Face Touchscre...
United States 
reb'2012 Davis Standard 6” Vented Extruder, 30:1 L/D 250hp 1990
- Manufacturer: Davis-Standard
r' 2012 Davis Standard Single 6" Screw Extruder model 60IN 60 TPIH 30:1 L/D Two-Stage Feed Screw: Replaced in 2012 ($21,000.00) 40’ Long Water Trough Multispeed Belt Puller 6”X36” (2 New Belts $721.00 ea.) H...
Davis Standard Sheetline
- Manufacturer: Davis-Standard
54" 3 Layer Sheetline Extruder Used Davis Standard Sheetline Extruder for Sale. This pre-owned Davis Standard plastic extruder is located in The United States and available to be seen under power for an inspecti...
USA- Trusted Seller
6" Davis Standard Egan / Berringer Water Ring Pelletizing Line
- Manufacturer: Davis-Standard
6" Davis Standard Egan / Berringer Water Ring Pelletizing Line Used 6" Davis standard Egan / Berringer water ring pelletizing line consisting of: 6" Davis Standard Egan extruder, model 6026-D.R.H, 44:1 l/d, elect...
Cleveland, OH - Trusted Seller
6" Davis Standard Egan Extruder, 44:1 L/D, 400 HP
- Manufacturer: Davis-Standard
6" Davis Standard Egan Extruder, 44:1 L/D, 400 HP Used 6" Davis Standard Egan extruder, model 6026-D.R.H, 44:1 l/d, electrically heated, water cooled barrel, jacketed feed section, vented barrel with vacuum pump,...
Cleveland, OH - Trusted Seller
3 Roll Sheet Stack Davis-Standard 1.25" Extruder Line
- Manufacturer: Davis-Standard
3 Roll Sheet Stack Davis-Standard 1.25" Extruder Line 10" 3 roll sheet stack line, consisting of: 1.25" Davis Standard extruder, model DSPW-125V-H24, 24:1 L/D, electrically heated, water cooled with circulation p...
Cleveland, OH - Trusted Seller
4.5" Davis Standard / Gala Underwater Pelletizing Line, 150 HP
- Manufacturer: Davis-Standard
4.5" Davis Standard / Gala Underwater Pelletizing Line, 150 HP Used 4.5" Davis Standard / Gala underwater pelletizing line with 4.5" Davis Standard Thermatic extruder, model 45IN45HT, 30:1 L/D, air cooled barrel,...
Cleveland, OH - Trusted Seller
DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M3316, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-12...
Hainesport, NJ - Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ - Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ - Trusted Seller
1997 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ 
DAVIS STANDARD 1/4″ TUBING EXTRUSION 17437
- Manufacturer: Davis-Standard
Davis Standard 1/4″ tubing extrusion line including the following equipment:A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barr...
Elk Grove Village, IL2.5" Davis Standard / Gala Pilot Plant Pelletizing Line – 75 kW Extruder, Underwater Pelletizer, Spin Dryer, 2020
- Manufacturer: Davis-Standard
- Model: 25
53759005 Used 2.5" Davis Standard/Gala Pilot Plant Pelletizing Line. 2.5" Davis Standard Extruder, Model 25, 24:1 L/D Ratio, 4 zones air cooled barrel, 75 KW HP Capacity, 1.25 SF, 17.26 to 1 gear reduction ratio,...
Belvidere, IL
DAVIS STANDARD 24″ X 48″ 17581
- Manufacturer: Davis-Standard
One (1) used 48″ Davis Standard cooling and polishing stand having three (3) nominal 24″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation. Rolls are pneumatically actuated. ...
Elk Grove Village, IL
DAVIS STANDARD 4.5″ 30:1 L/D 18937
- Manufacturer: Davis-Standard
One (1) used Davis Standard model 45IN45 extruder. S/N M3316. Shop order 05432. Extruder has 30:1 L/D ratio with a six (6) zone electrically heated, air cooled, and non-vented barrel at a 42″ center-line. Gearbox...
Elk Grove Village, IL
Tip: Enter manufacturer, model or keyword
