Used sit

1958 WALKER NEER 43 #1397T

• Manufacturer: Walker

Built 1958, trailer mounted, 3000’ capacity, sitting since 2015 Price: $40,000 - Oklahoma

LOOMIS CLIPPER 24 CABLE TOOL RIG #2613T

3 line machine, Continental gas deck engine, mounted on old Chevy that needs replacing, sitting for long time Price on Request – North Dakota KEYSTONE 50 CABLE TOOL RIG

SCHRAMM T64 DRILL RIG #9879Tb

• Manufacturer: Schramm

250 psi air compressor, Detroit 8V71 deck engine, mounted on 1976 GMC truck, rod box, winch, 200’ drill pipe, sitting for a while Price: $40,000

CYCLONE 46 #9582T

6 cyl gas deck engine, sitting over 15 years, needs new cable, includes tools, bailers, bits, stems, set of jaws Price: $32,500 - Pennsylvania

WALKER NEER C31 #8263Tc

• Manufacturer: Walker

Single pole, 3 lines, Waukesha deck engine locked up engine needs replacing or rebuilding, mounted on 1972 Chevy 2-ton truck, screw jacks been sitting for years Price: $25,500 - Kansas

1978 FRANKS 1256 WORKOVER RIG #530Tb

• Manufacturer: Franks

Manufactured 1978, 96’ x 180,000# 3 legged derrick, 75 ton hook block, mounted on 4 axle carrier with Detroit 8V92 diesel engine, been sitting a while Price: $115,000

FAILING 1500 AND MAYHEW 500 #2827R

• Manufacturer: Failing
• Model: 1500
• Transmission type: Mechanical
• Mast Height: 0.94 m

Short derrick (runs 10’ drill pipe), 1500 retractable table, 2-3/8” kelly, mechanical clutches, 5 x 6 Gardner Denver mud pumps, mounted on 1978 I6000 truck, Cat diesel engine, rig has been sitting over 9 years an...

1994 INGERSOLL RAND ECM 370 #14156c

• Manufacturer: Ingersoll Rand
• Model: ECM-370
• Horsepower: 215 hp

Manufactured 1994, sitting idle for a few years and will require some refurbishing to the air coupler, two pistons repacked, O-ring replaced, 5 rods and bit, 140 hammer Price: $37,000 GILL BEETLE MODEL 300C ROCK ...

FRANKS 844 #11696Tb

• Manufacturer: Franks

10 x 13” pole, single drum, mounted on 1980 Brigadier 9500 Series truck with 671 inline Detroit, drop box, travelling blocks, tubing lines, hyd jacks, no tooling, sitting since 2000 PRICE: $49,500

SPEEDSTAR 55 CABLE TOOL RIG #2819T

2 line machine, 42’ mast, Deutz diesel deck engine, mounted on 1985 Chevy C65 truck with gas engine, 2 rear mechanical jacks, no tools, sitting a while but starts up Price: $16,500

BUCYRUS ERIE 22W #7569T

• Manufacturer: Bucyrus-Erie
• Model: 22W
• Mast Height: 12.19 m

Continental 6 cylinder deck engine, mounted on (1990’s) International truck with V8 gas engine, 3 line machine, 2 rear mechanical jacks, tools for 4” holes, sitting since 2013 Price: $27,000 - Michigan

MAYHEW 1000 DRILL RIG #2577T

5 x 6 Gardner Denver mud pump, 5-1/2” stationary table, fluted kelly, mounted on Diamond Rio with 220 Cummins engine, PTO, sitting a long time Price: $30,000 GARDNER DENVER/MAYHEW 1000 DRILL RIG

BUCYRUS ERIE 20W #7581T

• Manufacturer: Bucyrus-Erie
• Model: 20W
• Drilling depth: 152.4 m
• Mast Height: 9.75 m

Ford gas engine on deck, 3 line machine, 36’ mast, mounted on 1980’ GMC Brigadier truck with Detroit engine, 3 hydraulic leveling jacks, tools for 5” wells, sitting since 2020 Price on Request – located Ohio

BUCYRUS ERIE 20W #15648T

• Manufacturer: Bucyrus-Erie
• Model: 20W
• Drilling depth: 152.4 m
• Mast Height: 9.75 m

3 line machine, diesel deck engine, mounted on 1990’s GMC single axle truck with gas engine, 2 rear manual leveing jacks, no tools, sitting over 10 years Price: $13,500 USD - Canada

BUCYRUS ERIE 22W #3884Ta

• Manufacturer: Bucyrus-Erie
• Model: 22W
• Mast Height: 12.19 m

Gas deck engine, 2 line (sandline and mainline), spud beam, mounted on 1972 Ford single axle truck with gas engine, 3 hyd jacks, tools for 4”, sitting a long time, needs TLC Price: $11,500 - Wisconsin