Used Processing in Illinois, USA

CDS CBH36-6 6″ X 36″ 18259

• Manufacturer: CDS

CDS model CBH 36-6 belt puller. S/N 230202. Has nominal 6″ wide belts with 36″ of belt contact length. Set up for right to left operation. Top and bottom belt manually height adjustable via hand wheel. Belts are ...

LORENZ 6″ OD DIVERTER 18210

• Manufacturer: Lorenz

Lorenz model DV2-600-11AL-ST-C 6″ OD diverter. S/N 35588-01. Has 6″ OK160 pipe adapters that can be removed to go back to 6″ OD flange less pipe. Aluminum construction

COPERION SMALL MATERIAL HOPPER 16768

• Manufacturer: Coperion Waeschle

Coperion Capital small material hopper CS series 36″ diameter barrel, 10″ straight side, 25″ long, 60-degree cone with 10″ top opening, 7-3/4″ ID outlet with 10.5″ OD bolt flange, Unit has four (4) stand mounts a...

LARGE FOREMOST VACUUM RECEIVER 18220

One (1) used Foremost vacuum receiver. With lid and flapper. Aluminum construction. 2.5″ OD inlet. 6.5 OD outlet

BERINGER 2 HP HYDRAULIC POWER 16824

• Manufacturer: Beringer

Beringer model HPNVL 2HP hydraulic power pack, S/N 4SL704-3. 2HP 230/460V motor with pump which are not mounted to the tank. Includes controls.

GAMMA FLUX 9 ZONE TEMPERATURE 16294

• Manufacturer: Gammaflux

Gamma Flux 9 zone hot runner controller, 240-Volts.

SPROUT WALDRON 1410-MST 10″ AIRLOCK 14267

• Manufacturer: Sprout Waldron

Sprout Waldron model 1410-MST airlock, S/N 82-0005, steel vanes with replaceable tips, 13″ x 13″ OD flange, 10″ x 10″ OD opening, no gearbox nor motor

AMBRITT 6″ DIAMETER X 50″ 14273

Ambritt feed rolls, no S/N. 6″ diameter x 50″ long steel, knurled rolls in off-set position. Pneumatic pinch. 25:1 Sumitomo gearbox with a 1.0 service factor. New 3 or 5HP motor included.

4″ DIAMETER X 24″ WIDE 12078

• Manufacturer: blades machinery

Knurled steel feed rolls, 4″ diameter x 24″ wide. Air operated feed roll. Pinch rolls are driven by a 2HP 180V 1,750 RPM DC motor through a 5.3:1 gearbox.

5″ X 12″ KNURLED STEEL 10107

Knurled steel feed rolls 5″ x 12″. Powered by a 1HP 230/460V AC motor into an Acrison, 60:1 gearbox. Upper roll is spring tensioned.

DUAL IN-FEED CUMBERLAND 2062B HOPPER 10200

• Manufacturer: Cumberland

Cumberland dual in-feed 2062B hopper with rear mounted 48″ wide paddle feed. Paddles powered by a 3HP DC 180-Volt motor through Boston gear F231D-24-B9 24:1 gearbox, chain and sprocket driven paddles.Two are avai...

18″ WIDE FEED ROLLS 5851

18″ wide feed rolls. Both rolls are 6″ diameter x 18″ wide. One (1) rubber and one (1) made of knurled steel. Pneumatically actuated by two pneumatic cylinders. Rolls are powered by a 2HP 230V/460V motor through ...

MOLD MASTERS MT-06-06 SIX ZONE 12777

• Manufacturer: Mold Masters

Mold masters model MT-06-06, six zone hot runner controller, S/N TMMT1210123 220-Volt, 3-phase operation, 40 Amp maximum load. Includes model VT12 power supply and a Square D 15 kVA transformer. Mounted on a cast...

MOLD MASTERS TMO-4220A10 HOT RUNNER 4904

• Manufacturer: Mold Masters

Mold Masters model TMO-422A10, S/N 92-0040. Hot runner controller, 4 zones, 230-Volt, digital display.

KEYSTONE CONTROLS 790-500 10″ BUTTERFLY 12873

• Manufacturer: Keystone RV

Keystone Controls model 790-500, S/N 73700B. 10″ pneumatically actuated butterfly valve, 120-Volt operation.Two are available.

Ingersoll Rand IRN100H-OF Industrial Compressor

• Manufacturer: Ingersoll Rand
• Model: IRN100H-OF

Good condition Ingersoll Rand IRN100H-OF Industrial Compressors. Located in USA and other countries. Click request price for more information.