Used machine tools in India

Billet Shear Valdarno

• Manufacturer: Valdarno

Cutting up to : 90 mm dia The billet share has a complete line of auto loader and auto stacke With billet Loader and Feeder

Billet Shear Basant

• Manufacturer: Basant

Cutting size : 4" Flying wheel 53 inches-thickness 290 mm, Gear- 44 inch- thickness : 11 inch, Main Shaft : 270 mm thick, Motor : 940 RPM 40HP, Main Gear : 44 inch dia, 11 inch thick, Main Shaft : 45 inch, ...

Billet Shear SCPK500

• Manufacturer: WMW Erfurt, Germany

Capacity : 500 tons, max cutting power : 500 tons, 25 SPM, permissable number of strokes, single 15 , rating of main motor : 22 kW, stroke of blank side : 100 mm, length of blade : 420 mm, length of stop,...

Ring Rolling Machine KRFW400

• Manufacturer: Wagner German

4 Station Table Type Ring Rolling Mill Max OD : 350 mm, Max Height : 100 mm. One person to load the ring and automatically the finished ring will fall in pallet. At a time 4 rings are on the turning table. C...

Billet Shear Wilkins & Mitchell

• Manufacturer: Wilkins & Mitchell

Capacity : 500 tons, Stroke per minute : 20, Billet dia. RCS 100 mm & Dia. 120 mm The Conveyor and Bar Shifter is also available with the equipment. The shear was working when removed for shifting. Technical...

Billet Shear Ficep F180

• Manufacturer: Ficep

Round cutting dia : 75 mm, Square cutting dia : 70 mm, Stroke length : 50 mm, Stroke per minutes : 60, Motor capacity : 25 HP (220 V 50 HZ).

Billet Shear Q42-500B

Max Cutting force : 5000 kn, Max cutting dia : 45-105 mm, Stroke : 33, Air pressure : 0.45-0.6 MPa, Motor power : 37 kW, Machine dimensions L x W x H : 4700 x 2540 x 4245 mm, Weight : 26 tons, With auto lo...

Billet Shear 214/680

• Manufacturer: Peddinghaus

Shearing force: 680 tons, Stroke: 100 mm, Stroke rate: 27 min^-1, Max. diameter of workpiece: 145 mm, Taper : 6 mm Max for diameter 4 mm Max for Square Total weight: 12 tons.

5 tons Hammer Forging Pneumatic Russian 17KP

• Manufacturer: Russian

Capacity : 5 tons, Blow energy : 125 KJ, Nominal weight of falling parts : 5000 Kg, Actual mass of dropping parts without the Upper tool : 5080 kg, Kinetic energy of the falling parts : 12500 kg min., Number...

Hammer Forging Pneumatic MPM1000

• Manufacturer: Huta Zygmunt, Polish

Capacity : 1 ton, Percussive energy : 3600 mkg, Ram weight : 1250 kg, Mode of operation pneumatic, Table size (front to back) : 700 mm, Stroke : 800 mm, Strokes : 10 min, Working pressure : 5-7 atm, Max. ...

Part Former Hot Line Hatebur AMP70

• Manufacturer: Hatebur

Hatebure AMP70 with 1200 KW Induction Heater with all coil sets and auxiliary equipment. Round job up to 170 dia. Profile job up to 180 mm in length. Production rate : 60/80 part per minute. Extra note: capac...

Cross Wedge Roll Smeral ULS100

• Manufacturer: Šmeral Brno
• Model: ULS 100

Slugs dia. : 35-100 mm, Max. slugs length : 500 mm, Max. rolled products length : 750 mm, Max. rolled products lengths with not reduced ends : 800 mm, Max. stock reduction with 1050 °C min. temperature : 75 %...

Ring Rolling Line Wagner dia 400 mm

• Manufacturer: Wagner

Wagner Ring Rolling Mill 1) Ring Rolling Machine Radial Horizonal type Make Wagner, Germany, Ring Dia : 75 - 400 mm Ring Height : 160 mm Capacity : 1000 K pcs, Bar dia : 35-80 mm, Weight : 0.5-6.0 kgs, 2...

Ring Rolling Line Sket Dortmund dia 850 mm

• Manufacturer: Sket

1) Dortmund Ring Rolling Machine, Model number : KFrWt600/K60034B, Ring Dia : 170 - 600 mm, Ring Height : 180 mm Speed of profile roll : 300 - 350 RPM, Working capacity : 900 K pcs, Bar dia : 60- 90 mm, We...