Used Processing in France

ITG Quenching & Tempering Line with Cutting Saw at the end for Sampling

• Manufacturer: ITG Indultionsanslagen

ITG Continuous quenching and tempering line – Tempering Final sampling cut via OHLER REMSCHEID saw for laboratory analysis. Different coils diameter according to tube sizes. Associated Equipment: – Transfer / rol...

Pilger Mill LP4

• Manufacturer: DMS MONTBARD

DMS MONTBARD Cold Pilger Mill, LP4 (1971) Crankshaft/engine reduction ratio: 0.25 *Reducer requires maintenance This lot is part of a combination lot: 20 Cold Pilger Mills Not the machine you are looking for? Sen...

Pilger Mill 4" 1/2, N°1

• Manufacturer: Mannesmann Demag - Meer

MANESMANN MEER Cold Pilger Mill, 4" 1/2, No.1 (1969) Crankshaft/engine reduction ratio: 0.18 This lot is part of a combination lot: 20 Cold Pilger Mills Not the machine you are looking for? Send us your requirements

Pilger Mill 4" 1/2, N°2

• Manufacturer: Mannesmann Demag - Meer

MANESMANN MEER Cold Pilger Mill, 4" 1/2, No.2 (2003) Crankshaft/engine reduction ratio: 0.18 This lot is part of a combination lot: 20 Cold Pilger Mills Not the machine you are looking for? Send us your requirements

Hot Sampling Saw and testing unit

Hot Saw to cut tubes sections for sampling Capabilities: Associated Equipment: – Sample elevator (transfer) to testing pulpit at elevated floor – VOLLMER excentricity testing equipment for samples cut after Rotar...

LIMAB measurement after Rotary Sizer Mill

• Manufacturer: LIMAB

Performs continuous measurement of tube geometry immediately after the rotary sizer stage. This lot is part of a combination lot: 10 Hot Rolling Mill Not the machine you are looking for? Send us your requirements

14-Stands Calibration Mill (Calibreur)

• Manufacturer: DMS MONTBARD

Capacity: Associated Equipment: – 90 bar pump high-pressure descaling system before first stand – Guiding system for tube alignment into the rolling stands – Stands’ maintenance related equipment Motor & Drive: –...

ZUMBACH Laser Measurement after Elongation Mill

• Manufacturer: Zumbach

Function: – Continuous, non‑contact measurement of tube outside diameter (OD) and ovality using laser beam Position: – Immediately after the elongation mill, before calibration and sizing Capability: SCHNEIDER PL...

Billet Cutting Station

• Manufacturer: CENTROCUT

Fully automated billet cutting line including: (2) Saw Cutting Machines, individual 462 W motors, common (shared) hydraulic unit, Inlet conveyors, Outlet conveyors, scrap conveyors,control system,80 to 240 mm bil...

Hot Rolling Mill

Hot Rolling Mill Equipment Combination Lot of the following: Lot No. 1100Hot Sampling Saw and testing unitLot No. 1110Hot Tubes Cooling BedLot No. 107014-Stands Calibration Mill (Calibreur)Lot No. 1080Rotary Size...

Central Workshop

• Manufacturer: Cutler-Hammer

Maintenance, tooling, and fabrication support for tube production and finishing lines. Enables in‑house repair, adjustment, and preparation of mechanical components, cutting tools, and fixtures. Combination Lot o...

1988 Goavec – 10000 L process tank (A)

• Manufacturer: Goavec SA

Material : 304 stainless steel (Thickness : 25/10) Removable guardrail Drawing available (digital version)

Impact Charpy testing machine INSTRON

• Manufacturer: Instron

INSTRON type Impact Charpy Testmodel 300 MPX 1438 n°XL (2011) This lot is part of a combination lot: 70 Laboratory Not the machine you are looking for? Send us your requirements