Used Machine Tools in Shizuoka, Japan

OSG P5D1500FS20M04
- Manufacturer: OSG
OSG-PHOENIX 15mm/5D type indexable drill P5D1500FS20M04 unopened Diameter 15mm, machined hole depth 75mm, maximum machined diameter 15.8 nn, total length 140mm, shank diameter 20mm, shank length 50mm, 2-flute Th...
Hamamatsu, Japan
Kyocera DRZ
- Manufacturer: Kyocera
Kyocera 25mm / Magic Drill DRZ S25-DRZ2550-08 Cutting edge diameter 25mm Shank 25mm Overall length 133mm 2-flute
Hamamatsu, Japan
FUJIGEN CTL-00T
- Manufacturer: Fuji Gen
FUJIGEN Equilateral Triangle 60°/Cartridge for Gut Tender CTL-00T Equilateral triangle 60° tip, shank diameter 18φ, keyway width 4,95mm, overall length 117mm, no back teeth
Hamamatsu, Japan
Hitachi Tool ARL3032R
- Manufacturer: Hitachi
Hitachi Tool 32mm / Rapid-Cutting Type Alpha Radius Mill ARL3032R Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 5mm, Shank 32mm, Length under neck 120mm, Total length 200mm, 3 blades
Hamamatsu, Japan
Hitachi Tool AR
- Manufacturer: Hitachi
Hitachi Tool 32mm / Rapid-Cutting Type Alpha Radius Mill AR ARS3032R Flat/groove coarse/medium coarse Cutting edge diameter 32mm, maximum depth of cut 5mm, shank 32mm, length under neck 70mm, total length 150mm, ...
Hamamatsu, Japan
Hitachi Tool ASR
- Manufacturer: Hitachi
Hitachi Tool 32mm/Alpha High Feed Radius Mill ASR ASRS2032R-5 Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 2mm Shank 32mm, Length under neck 70mm, Total length 150mm, 5 blades
Hamamatsu, Japan
Mitsubishi Materials FSTU212R
- Manufacturer: Mitsubishi
MITSUBISHI MATERIALS Holder for machining of equilateral triangular 60° internal diameter FSTU212R Internal diameter, through-hole/edge face, stop hole, copying, minimum machining diameter 16mm, depth of cut 93°,...
Hamamatsu, Japan
Hitachi Tool ASR
- Manufacturer: Hitachi
Hitachi Tool 32mm/Alpha High Feed Radius Mill ASR ASRS2032R-5 Flat/groove Coarse/medium coarse Cutting edge diameter 32mm, Max. depth of cut 2mm Shank 32mm, Length under neck 70mm, Total length 150mm, 5 blades
Hamamatsu, Japan
S25RMCLNL12
- Manufacturer: Tomoe Co. Ltd.
Rhombic 80° Internal Diameter Holder S25RMCLNL12 Min. machining diameter 32, 0° relief angle, 95° depth of cut, shank 25, with oil hole, left-hand side, multi-clamp type
Hamamatsu, Japan
2020 Dymac R40
- Manufacturer: Daimaku
Dymac 400mm NC Roll Feeder R40 Width-400mm Thickness-3.2t Feed length 0.01mm-9999.99mm 80 width/3.2t 200 width/2.6t 300 width/1.6t Left → Right
Hamamatsu, Japan
Tungaloy EXN03R025M25
- Manufacturer: Tungaloy
Tungaloy 25mm / Threaded high-feed cutter EXN03R025M25,0-05-C Opened for filming Flat/ Groove/ Slanted notch / Vertical Cutter diameter 25mm, maximum cutting depth 1mm, shank diameter 25mm, neck length 60mm, over...
Hamamatsu, Japan
2012 Orii AFC05GAFP
- Manufacturer: Orii
ORI 500mm NC Roll Feeder AFC05GAFP Width 20mm-500mm Thickness 0.2t-3.2t Top speed: 1.0m/sec Left→Right
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/ Shoulder facing cutter straight shank PSE11R030SS32-3L Plain/Side/V-Groove rough-finish processing outer diameter 30mm maximum cutting depth 10mm shank 32mm neck length 90mm overall length 190mm...
Hamamatsu, Japan
Rhombic 35° OD Turning Holder
- Manufacturer: Tomoe Co. Ltd.
Unknown Rhombic 35° OD turning holder One-round length of the sheet approx. 15,3mm Total length 150mm Shank 25×25 right hand side
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/ shoulder turning cutter straight shank PSE11R030SS32-3L Plane/side/groove rough-finish processing outer diameter 30mm maximum cutting depth 10mm shank 32mm neck length 90mm overall length 190mm ...
Hamamatsu, Japan