Used Plastic/Rubber Processing in New York, USA

50 GALLON DRUM OF HUNTSMAN FOAM-LOCK500 - UN-OPENED VIRGIN MATERIAL

50 GALLON DRUM OF HUNTSMAN FOAM-LOCK500 - UN-OPENED VIRGIN MATERIAL

50 GALLON DRUM OF HUNTSMAN B-SLIDE RESIN HEAT LOK-HF0 HIGH LIFT, UN-OPENED VIRGIN MATERIAL

• Manufacturer: Resina

50 GALLON DRUM OF HUNTSMAN B-SLIDE RESIN HEAT LOK-HF0 HIGH LIFT, UN-OPENED VIRGIN MATERIAL

Belovac BV C-Class

• Manufacturer: Belovac

Machinery specification provided by manufacturer:Sheet size 48'' x 96'' (122 x 244cm) Seven zone oven, PLC Plug assist Depth of draw 22'' Fully adjustable material clamping Recommended for plastics ABS - PVC - PE...

BROWN MACHINE R244

• Manufacturer: BROWN MACHINE

Information provided by present owner Used 4 Brown station Rotary Thermoformer Model 244 48”x 96” Mold. S/N 6158 Preheaters frame size 57”x93”, Preheaters top and bottom: 14ea (Rod Heaters) Main Heater frame size...

1997 Custom Manufacturers TS6096

• Manufacturer: Custom Built

1997 Custom Manufactures 5’x8’ twin sheet rotary 50” top stroke 50” bottom stroke electric rotate ceramic ovens 14 zone top / 14 zones bottom

1987 BROWN MACHINE R-224

• Manufacturer: BROWN MACHINE

Brown R-224 Rotary Thermoforming Machine. 2 Moving Platforms 2 Heating Banks 4 Stations; Load, Unload, Heat, Form 480 V. 3 Phase Top and bottom Natural Gas Oven Fully Operational 48” stroke each platen 1987 7 x 1...

2000 BROWN R223E

• Manufacturer: Brown

Brown R-223-E Rotary Thermoformer is in good working condition. built in 2000 Platen size of 42" x 72" and Platen height of 24". top and bottom oven, with top and bottom platen Panelmate touch screen control has ...

BROWN MACHINE TS72120

• Manufacturer: BROWN MACHINE

New Platens new motors new oven- ceramic new rotate new PLC controls, New touch screen HMI new wiring, new plumbing new valves & cylinders new clamp frames new vacuum system closed loop lift table cooling fans 48...

2022 Belovac BV E Class

• Manufacturer: Belovac

Used 2022 Model BV E Class. 53" x 53" Vacuum Former 50 hours used Depth of draw 20" Vacuum system Independent tank with 1HP High CFM Vacuum pump Power: 240 3 phase, Neutral required for 110v components (480 Volt ...

2001 PLASTI-VAC (PVI) 6120XX

• Manufacturer: PLASTI-VAC (PVI)

Used Plasti-Vac Inc (PVI) Vacuum Thermoformer Model 6120XX Former, Allen Bradley PanelView Plus 600 Controls, S/N P6120XX-1894-101; new 2001 vacuum pump and tank, PVI Model 612TD Poly Carbonate Sheet Dryer

ZMD INTERNATIONAL 48x96

• Manufacturer: International

48'' x 96'' ZMD ThermoformerMFG. By Z.M.D. International Inc. Single station Forming area 48'' x 96'' Stroke on bottom platen about 24'' Stroke on top platen about 36'' 30'' daylight bottom platen 42'' daylight t...

ZED 18'' x 24'

• Manufacturer: Zed

Used Zed 18x24 vacuum former 18'' x 24'' forming area depth of draw 4" roll or sheet fed Film fed manually, clamped in place, retractable heater moves over film and is timed to prepare the film for forming, the h...

SHUMAN DHXJ

• Manufacturer: SHUMAN

Model DHXJ Maximum Forming Area 120" x 120" Heat Source Open Coil Top & Bottom Ovens Yes # of Top Zones 15 # of Bottom Zones Controls Dual PLC Vacuum Pump Included Vacuum Tank Voltage 600V Note Comes with Spare E...

PLASTI-VAC (PVI) 4100XX

• Manufacturer: PLASTI-VAC (PVI)

Model 4100XX 48" X 120" MAXIMUM MOLD SIZE TOP HEAT OVEN CONTROLLER Volts 220 Amps 180 Cycle 60 3 phase 4' x 10' forming area