Used Ball Mills (Mineral Processing)

HOSOKAWA 800/3 AFG

• Manufacturer: Hosokawa
• Model: AFG 800

Used Hosokawa Alpine 800/3 AFG, fluidized bed opposed jet mill. Mild steel, (3) 50 hp motors, 3 PH 60 Cy 460 volts (4) grinding nozzles. Nominal air flow rate. Nm3/H8400. Includes Mikropul Cyclone model V/EE 22/87.

HOSOKAWA 100 AFG

• Manufacturer: Hosokawa
• Model: AFG

Used Hosokawa multiprocessor ZPS milling machine including an upside down Acm with ATP classifier and Hosokawa / Alpine 100 AFG counter jet mill with 55kW compressor powered by a 1.0 kW motor operating at 22,000 ...

9 x 7 ft Allis Chalmers Ball Mill

• Manufacturer: Allis-Chalmers

- 9 ft dia x 7 ft length ball mill - Manufactured by Allis Chalmers - Configured for wet grinding and overflow discharge - Mill components disassembled, inspected, cleaned, refurbished, and painted - mill shell w...

5 x 9 Ft. NEW Manufacture Ball Mill

- New manufacture 5 x 9 ball mill - Manufactured in Europe by DAI - 60 Hz electrical - Offered complete with components described below: - Cast steel heads, bearings housings, and gears NDT tested using dye-penet...

7 x 5.5 ft Ball Mill with 100 HP

- 7 x 5.5 ft grinding volume - 100 HP induction motor - Scoop feeder - Shell access door - 8" bull gear face - 18 tooth pinion gear - Straight cut gear teeth - I-beam steel skid - Babbitted trunnion bearings - Be...

13 x 18.6 ft Nordberg Rod/ Ball mill with 1,500 HP

• Manufacturer: Symons - Nordberg

- 1500 hp (1125 kw) AC 60 Hz synchronous motor, 225rpm - Eaton Fawick air clutch 46VC 1200 - Mill shell and cast heads - Feed and discharge trunnions and liners - Trunnion bearing assemblies - Refurbished girth g...

9 x 12 ft. Allis Chalmers Rod or Ball Mill with 400 HP

• Manufacturer: Allis-Chalmers

9 x 12 ft. Allis Chalmers Rod or Ball Mill w/ 400 hp - Herringbone (1 piece) bull gear, 302 teeth, 20 in. face - Herringbone pinion, 30 teeth, 20 in. face - Westinghouse 400hp, 750 rpm, 575 volts - Model SR-2614 ...

6 x 17 Ft. Marcy Ball Mills

- Used Refurbished Marcy Ball Mills - 2 Available - 17 ft. 19 in Long x 6 ft. 4 in. Width - 450 HP Weg Motor, 480 volt - Soft Start Motor System - David Brown Gearbox G17 9:1 ratio - Voith.562 EPK Clutch ...

5 x 7 ft (1.5 x 2 m) Allis Chalmers Ball Mill

• Manufacturer: Allis-Chalmers

- Rebuilt, unused, and ready to ship - In excellent condition - Configured for overflow discharge wet or dry grinding with rubber liners - Mill feed and discharge heads, bull gear and pinion gear inspected and ND...

1.5 x 3 m (~5 x 10 ft) New ball mill

- New unused ball mill made in North America - 1.5 x 3 meter internal shell dimension, less liners - Single piece rolled steel shell - Tire Driven - Rubber liner package with installation hardware - Rubber lined ...

Hardinge 8ft Dia. x 4ft Long Conical Ball Mill

• Manufacturer: Hardinge

With Cyclone Feed and Eriez Vibrating Pan Feeder With Operating Base and Grinding Media

10.5 x 18.5 ft Unused Outotec Ball Mill with 1,000 HP

• Manufacturer: Larox

- Unused surplus Outotec ball mills - 2 matching units available - Delivered to site, never installed or operated - 10.5 x 18.4 ft mill shell (3.2 x 5.6 m) - Cast mill heads - Trunnion supported mill - Ring and p...

18 x 27 ft (5.5 x 8.1 m) Citic Ball Mill with 5,500 HP

Unused 18 x 27 ft (5.5 x 8.1 m) Citic Ball Mill with 5,500 HP (4,100 kW) 893 RPM WRIM induction motor. - Rubber liners, 2 sets - High- and low-speed drive couplings - Sole plates Additional motor info: -WRIM - 89...

10 x 14 ft (3 x 4.3 m) Marcy Ball Mill with 800 HP

- Overflow discharge - Previously NDT tested - Lincoln gear-spray lubrication system - March 650-AL trunnion bearing lubrication system - New spare bronze insert - Ring gear - Pinion - Eaton Airflex 28VC650 dual ...