Air X Changer 132-2Z Gas Cooler Job # 087335
new
- Manufacturer: Air X Changer
Air X Changer Gas Cooler Model: 132-2Z Customer Number: E01157 Job Number: 087335
Hueysville, KY
Ariel JGC-6 - 3000 HP Electric Drive Four Stage Compressor Skid
new
- Manufacturer: Ariel
- Model: JGC
Compressor Skid with scrubbers and gas cooler only available Originally designed for a 3000 HP Motor and Ariel JGC-6 Frame Four Stage Size 24.125" x 24.125" x 24.125" x 20.125" x 12.5" x 7.25" Original P&ID Dr...
Hueysville, KY- Trusted Seller
500 Ton Toshiba ISGS500V10-27AT
used
- Manufacturer: Toshiba
- Model: ISGS500V
(2 machines available) 500 Ton Toshiba ISGS500V10-27 Shot size: 48 Oz Controller: Injectvisor V10 Tie bar spacing: 34.2" x 34.2" Platen Size: 48.4" x 48.4" The machines are in good running conditions.
Babbitt Pot
used
- Manufacturer: Ben Jones Machinery
Babbitt Pot & Dispenser - electric babbit pot with dispenser spout
Lancaster, KY- Trusted Seller
Cincinnati Milacron 2200 Ton VL-2200-413
used
- Manufacturer: Cincinnati
2200 Ton Cincinnati Milacron VL-2200-413: Shot size: 413 Oz. Tie bar spacing: 72.4" x 63.7" Platen Size: 101.18" x 92.72" Max. Open daylight: 135.43" Control: Camac 486C Voltage: 480 volts Equipped with: R...
Bowling Green, KY - Trusted Seller
Arburg Injection Molding hydraulic Pressure Gauge
used
- Manufacturer: Arburg
Arburg Injection Molding Hydraulic Pressure Gauge 6 Position Item is used. INV # P-70 Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.
$200 USDHenderson, KY - Trusted Seller
MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power
used
- Manufacturer: Mitsubishi
“Pulled from working Mitsubishi Molding Machine” MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power Supply Board INV# P-1327
$200 USDHenderson, KY - Trusted Seller
Conair 10721301 Dryer Input/Output Board - Free Shipping
used
- Manufacturer: Conair
🔥Conair 10721301 Dryer Input/Output Board - Free Shipping INV# P-1517
$350 USDHenderson, KY - Trusted Seller
(NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine
new
- Manufacturer: Van Dorn Demag
🔥 (NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine 15 Holes. Female Thread for the Nozzle is about 60mm. About 5-5/8" Diameter NOTE: We think this is for a 350 Ton Press. Ask all questions ...
$500 USDHenderson, KY - Trusted Seller
6" Diameter Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323
used
- Manufacturer: American
“Pulled from machine with low hours” Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323 About 12" Long by 6" in Diameter ITM# P-177
$500 USDHenderson, KY - Trusted Seller
(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE
used
- Manufacturer: Mitsubishi
“Pulled from working machine” 🔥(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE INV# P-1302
$1,000 USDHenderson, KY 
Louisville, KY
GRIEVE BF-122412-HT, BT-122012
used
- Manufacturer: Grieve
GRIEVE OVER/UNDER FURNACE MODEL BF-122412-HT w/TEMPERING FURNACE MODEL BT-122012 460V 3 Phase 26 Amps 20 KW 26 Amps -Workspace Dimensions: upper - 12" wide x 24" deep x 12" high; lower - 12" wide x 20" deep x 12"...
- Trusted Seller
5V21210 Cast Iron V-Belt Pulley 10 Groove 21.20 in O.D J Series Bushing
used
🔥5V21210 Cast Iron V-Belt Pulley 10 Groove 21.20 in O.D J Series Bushing Small chip on the outside edge can be viewed in the picture. Shouldn't affect anything. Contact for freight quote. INV# P-1814
$400 USDHenderson, KY - Trusted Seller
(2) NEW RAYCHEM PENTAIR E-100-L2-A / E100L2A (BRAND NEW) E-100-L-E
new
- Manufacturer: Pentair
🔥 (2) NEW RAYCHEM PENTAIR E-100-L2-A / E100L2A (BRAND NEW) E-100-L-E WHAT YOU SEE IS WHAT YOU GET INV# P-1128
$300 USDHenderson, KY
Tip: Enter manufacturer, model or keyword
