DECKEL MAHO DMG-DMC60T RS3 in Germantown, WI, USA
Used
Doubleclick to zoom in
Contact the seller for
additional photos and information.
Specifications
- Condition
- used
- Year
- 2005
- Stock number
- 063992
- Status
- Available
- Number of axis
- 5-Axis
- Tool changer
- 120 ATC
- Control
- HH TNC 530
- Spindle
- 24,000 rpm
- Spindle taper
- HSK-A63
- X axis
- 30.71" (780 mm)
- Y axis
- 22.05" (560 mm)
- B axis
- -120/+30 degrees
- Z axis
- 22.05" (560 mm)
- C axis
- 360 x 0.001 degrees
- Traverse range x (longitudinal)
- 30.71" (780 mm)
- Traverse range y (transverse)
- 22.05" (560 mm)
- Traverse range z (vertical)
- 22.05" (560 mm)
- Volume machining area
- 245 dm-3
- Rotation range
- 360 x 0.001 degree (Full 4th Axis)
- Clamping surface
- 19.7" x 24.8" (500 mm x 630 mm)
- Number of pallets
- 5 total (4 in changer, 1 in the machining cabin)
- Maximum table load
- 880 lbs (400 kg)
- Centre bush
- 2" (50 mm) diameter
- Torque 40% duty cycle
- 1,807 ft lbs (2,450 Nm)
- Holding momentum 40%
- 1,807 ft lbs (2,450 Nm)
- Maximum feed
- 7,200 degrees per minute
- Maximum table speed
- 30 rpm
- Positional uncertainty p
- 9 arc seconds
- Pallet change time
- Approximately 10 seconds
- Swivel range
- 150 degrees (-120/+30 degrees)
- Holding momentum with clamping
- 2,655 ft lbs (3,600 Nm)
- Rapid motion b-axis
- 35 rpm
- Type
- Digitally controlled
- Cooled drive
- Water
- Power 40% ed
- 34.9 hp (26 kW)
- Power 100% ed
- 25.5 hp (19 kW)
- Spindle speed range
- 24,000 rpm
- Acceleration/deceleration 0-24,000 rpm
- 3.5 seconds
- Number of gear steps
- None
- Spindle torque 40% ed
- 62.7 ft lb (85 Nm)
- Spindle torque 100% ed
- 44.2 ft lb (60 Nm)
- Clamping power
- 8 kN
- Drive cooled x/y/z
- Air/Air/Water
- Feed rate x/y/z
- 590 ipm (15 m/min)
- Rapid feed rate x/y/z
- 1,968 ipm (50 m/min)
- Maximum feed rate x/y/z
- 1,968 ipm (50 m/min)
- Acceleration x/y/z
- 0.6 g IN ALL AXES
- Feed power x/y/z
- 7/7.2/10 kN
- Magazine pockets
- 120
- Maximum tool weight
- 17.64 lbs (8 kg)
- Maximum tool diameter without free pockets
- 3.15" (80 mm)
- Maximum tool diameter with free pockets
- 6.3" (160 mm)
- Maximum tool length
- 12.4" (315 mm)
- Pump output
- 10.6 gallon/minute (40 l/min)
- Pump pressure
- 22 PSI (1.5 bar)
- Category
- Machining Centers in USA
- Subcategory
- 5-axis machining centers
- Listing ID
- 83657304
Description
5-AXIS MACHINING CENTERS
DMG-DMC60T RS3
SUBJECT TO AVAILABILITY, AND TERMS AND CONDITIONS FOLLOWING, WE OFFER FOR YOUR CONSIDERATION:
2005 DMG DECKEL MAHO DMC60T RS3 5-AXIS UNIVERSAL MACHINING CNTR WITH 5 PALLETS:
Made in Pfronten, Germany
-WORKING RANGE-
Max workpiece dims 23.62"(600mm)diameter,22.64"(575mm)height,882lbs(400kg)
-RS3 ROTARY PALLET CHANGER WITH INTEGRATED NC ROTARY TABLE (C-AXIS)-
-Stable compact construction with optimal linkage to guideway (Y-Axis)
-NC rotary table with direct measuring system
-Backlash-free preloaded precision spur gear for high rigidity, precision
and high torque, maximum holding momentum in closed loop
-High rapid feed rate
-Pallet changer allows setup parallel to production time
-SWIVEL MILLING HEAD WITH PROGRAMMABLE B-AXIS-
-Integrated 24,000 rpm motor spindle
-High pressure coolant supply centrally through spindle centre
(30 degrees past horizontal,horizontal,vertical,30 degrees past vertical)
150 degree swivel range allows UNDERCUTS and machining at NEGATIVE ANGLES
due to the swivel range of 30 degrees across the horizontal or vertical
axis.This gives you advanced flexibility for complex parts like impellers.
Swivel momentum milling spindle (40% duty cycle) 1,620 ft lbs (2,200 Nm)
Holding momentum without clamping (40% duty cycle) 1,438 ft lbs (1,950 Nm)
Swivelling time of the head from horizontal-vertical & vice versa 1.5 secs
-INTEGRATED MOTOR SPINDLE-
-FEED DRIVES-
Ball Screw Spindle X/Y/Z 1.57"x0.8" (40x20 mm) X&Y,1.97"x0.8"(50x20mm) Z
-120 POSITION VERTICAL CHAIN AUTOMATIC TOOL CHANGER-
Tool change time Approximately 0.8 seconds, double gripper tool changer
Chip-to-chip time Approximately 4 seconds vertical, 10 seconds horizontal
-EXTERNAL COOLANT SUPPLY ON THE OUTSIDE OF THE SPINDLE-
-PRODUCTION PACKAGE-
-238 gallon (900 l) coolant unit capacity
-Automatic paperband filter cleaning with fine filtering of the complete
emulsion to less than 50 um
-Cleaning of the spindle taper HSK-A63 by spindle air blast for high
permanent precision also for cleaning with frequent tool changes
-580 PSI (40 bar) 6 gallon/min (23 l/min) coolant thru the spindle centre
-Rotating clear-view window in cabin pane
-Chip flushing inside work cabin
-Chip conveyor (scraper flight conveyor)
-MACHINE IS EQUIPPED WITH-
Heidenhain iTNC530 3D Contouring CNC Control with:
-Electronic handwheel
-2nd processor card with Windows 2000
-OMAT Adaptive control for automatic feed rate adjustments
-Application Tuning Cycle ATC
Heidenhain infrared parts measuring probe
BLUM Laser tool length and diameter measuring, horizontal/vertical
Cooling by air blast through spindle centre, selected with M-function
Spray pistol with pump
Multi input transformer
Heidenhain glass scales direct measuring system X/Y/Z Axes
Heidenhain rotary encoders direct measuring system B/C Axes
External coolant nozzles on outside of spindle air/coolant selectable
Automatic switch-off of positive air pressure for the main spindle after
work end
Linear roller guideways and digital drives. Stability and high precision
are ensured with roller guideways with over-dimensioned distances between
the guideways. The table centre of gravity moves in between the vertical
guideways (Z-Axis).
Electronic temperature compensation
Spindle chiller
Available books and manuals
Full enclosure of machining area for safety and noise reduction
Sensitive machine parts (measuring systems, limit switches, guide-ways,
drives) are seperate from the machining area
Rotary Pallet Storage RS3 including 3 pallets
Oil and emulsion mist separator electrostatic filter
Minimum lubrication
Laminated Safety Glass for window in cabin door
Clamping hydraulics working table and set-up station for hydraulic
clamping devices