Machine Tools » Thuringia

Building Filters

26

Used rollers in Thuringia, Germany

  • Trusted Seller
    Auction
    no-image_en.png

    2014 electrohydraulic bandsaw MEP Shark 332 SXI evo

    • Manufacturer: MEP
    • Model: Shark 332

    semi-automatic, weight: 670 kg, with control terminal, and roller conveyor about 20x300 cm, mounted on supports

    Ellrich, Germany
    Visit Auction Website
  • Trusted Seller
    2013 Ernst Neptun EKB

    2013 Ernst Neptun EKB

    • Manufacturer: Ernst

    a deburring machine Ernst Neptun EKB year of manufacture 2013 the machine has first deburring roller, then comes the wide belt to make a grinding and finally comes two fleece rollers that run against each other ...

    Erfurt, Germany
  • KEPROMA AG DOD 40/100

    KEPROMA AG DOD 40/100

    • Manufacturer: ambold pressen- und maschinenbau

    - Demonstration model with branded overhauled control system - NC roll feed servo power with direct drive - plasma nitrided rolls - backlash free drive - strip side guide Performance data at 180 degrees - 1000 st...

    Schmölln, Germany
  • Holzmann ring bending machine RBM28

    Holzmann ring bending machine RBM28

    • Manufacturer: Holzmann

    Product Information "Holzmann Ring Bending Machine RBM28" Motor Data Motor Power S1 in W 1100 Voltage 400V / 3 / 50Hz Weight Net Weight in kg 230 Gross Weight in kg 260 Shipping Dimensions Packaging Height in mm ...

    $2,118 USD
    Ilmenau, Germany
  • 2007 EBU HK 200 FR

    2007 EBU HK 200 FR

    • Manufacturer: EBU
    • Model: HK 200 FR

    – Hydraulic clutch – Fixed table – Hydraulic overload protection in the ram – Hydraulic connecting rod clamp – Motorized ram height adjustment 120 mm with digital display of the set ram height, rapid and creep sp...

    Schmölln, Germany
  • Holzmann univ. sheet metal working

    Holzmann univ. sheet metal working machine 3 IN 1...

    • Manufacturer: Holzmann

    Product information "Holzmann univ. sheet metal working machine 3 IN 1 UBM760" General dimensions Working length in mm 760 Sheet metal processing Max. sheet thickness in mm 1 Round bending rollers Ø in mm 38 Max....

    $847 USD
    Ilmenau, Germany
  • Holzmann feed unit SF 444N-8

    Holzmann feed unit SF 444N-8

    • Manufacturer: Holzmann

    Product information "Holzmann SF 444N-8 feed unit" Motor data Vorschubgeschwindigkeit 3,5/5/7/10/12/17/26/34 Motor power S1 in W 750 Motor power S6 in W 1050 Voltage 400V Feed units Feed roller diameter in mm 120...

    $1,059 USD
    Ilmenau, Germany
  • Holzmann feed unit SF 344N-8

    Holzmann feed unit SF 344N-8

    • Manufacturer: Holzmann

    Product information "Holzmann SF 344N-8 feed unit" Motor data Vorschubgeschwindigkeit 3,5/5/7/10/12/17/26/34 Motor power S1 in W 750 Motor power S6 in W 1050 Voltage 400V Feed units Feed roller diameter in mm 120...

    $953 USD
    Ilmenau, Germany
  • BAD SALZUNGEN MHD 250/4

    BAD SALZUNGEN MHD 250/4

    • Manufacturer: ambold pressen- und maschinenbau

    unbraked reel with pressure roller new painted Control type: conventional | Storage location: Schmölln | Freight basis: In stock | Sheet width: 250 mm | Coil weight: 2,5 t | Inner coil diameter: 450 - 530 mm | Sh...

    Schmölln, Germany
  • GSW-SCHWABE MHM 1,5/1250

    GSW-SCHWABE MHM 1,5/1250

    • Manufacturer: Herman-Schwabe

    - Manual spreading - motor-driven - pressure roller - new lacquering

    Schmölln, Germany
  • 1986 KAISER V 40 W/680

    1986 KAISER V 40 W/680

    • Manufacturer: Kaiser
    • Model: V 40 W/680
    • Power requirement: 8 kW

    - Tappet with 2 connecting rods - Unidor tool monitoring - Kaiser right gripper feed, band width 180 mm, feed length 150 mm, max. 2nd mm - Kaiser scrap scissors on the left - soundproof cladding - Eccentric shaft...

    Schmölln, Germany
  • BAD SALZUNGEN MR + MHD

    BAD SALZUNGEN MR + MHD 250/4

    • Manufacturer: ambold pressen- und maschinenbau

    Reel MHR 250/4: gr. coil diameter: 1400 mm Inner coil diameter: 450 - 530 mm unbraked reel with pressure roller Straightening machine MR 250/4: Coil infeed height: 1250 mm The machine was dismantled, checked and ...

    Schmölln, Germany
  • SCHLEICHER

    SCHLEICHER

    • Manufacturer: Schleicher

    Straightening machine, 7 rollers, Schleicher, type RM 6-95/160 Strip width: 300 mm Strip thickness: 2 – 4 mm Straightening cross-section: 1200 mm² Voltage: 220/380 V 50 Hz Power: 3.1 kW Reeler with pressure rolle...

    Schmölln, Germany
  • 1990 HELMERDING ERH 75 B

    1990 HELMERDING ERH 75 B

    • Manufacturer: HELMERDING

    Furnishing: - with hydraulic clutch-brake combination, with new hydraulics and oil cooler - with gear train in an oil bath - Fixed table prepared for hanging tool changing consoles - 2 roller strips in the table ...

    Schmölln, Germany
  • Holzmann nylon grinding roller for

    Holzmann nylon grinding roller for ZS560FU

    • Manufacturer: Holzmann

    Product information "Holzmann nylon sanding roller for ZS560FU". Further links to "Holzmann nylon sanding roller for ZS560FU" Questions about this article? show other products from HOLZMANN

    $741 USD
    Ilmenau, Germany
12

Overview

Machine tools are devices used in manufacturing to shape or machine metal and other rigid materials, typically by cutting, boring, grinding, shearing, or other forms of deformation. They are essential in producing precise and complex parts in industries such as automotive, aerospace, and electronics, and include a variety of machines like lathes, milling machines, and CNC machines.

FAQ

What should I consider when buying a used machine tool?

Evaluate the machine's condition, age, and maintenance history. Check for any signs of wear or damage and ensure it meets your specific production requirements.

How do I ensure the machine tool is shipped safely to my location?

Hire a transport service experienced in moving heavy machinery. Ensure the machine is properly secured and protected to prevent damage during transit.

What is the maintenance schedule for machine tools?

Regular maintenance includes lubricating moving parts, inspecting for wear and tear, and calibrating for accuracy. Follow the manufacturer's guidelines for specific maintenance tasks and intervals.