Used processing

GALA 38" x 39"

• Manufacturer: GALA

Used Gala SS bin only. Square construction, 38" x 39" with hinged top cover on 1/3 of top of bin, and openings on balance of 2/3. No pumps or filters included.

MATSUII DMZ-120

• Manufacturer: MATSUII

Used Matsui dehumidifying dryer. Model DMZ-120, Serial #01464, new 1995. Rated at 120 CFM. Has 3 KW heater, 230 volt, 3 phase, 60 hertz. Includes hopper mounted on a portable stand.

2006 Scheer Bay WAA300

• Manufacturer: Scheer

Used 13.5" wide Scheer Bay Model air knife. Model WAA300, Serial #WAA300-0582, new 2006. Driven by a 7.5 HP Baldor Super E motor, 460 volt 3 phase 60 hertz. Includes starter and controls. Caster mounted. Previous...

6.75" Wide

Used 6.75" Wide Air Knife. Top/bottom air input. 72" work height. Includes 1 hp blower, 208-230/460 volt.

2002 COPERION 2.3"

• Manufacturer: Coperion Waeschle

Used 58mm Coperion Co rotating Mega Compounder with 11 barrel sections (34/1 L/D) and side feeder, New 3/2002. Has electrically heated water cooled barrel. Direct connected to 500 hp DC motor with SCR controller....

BUSS 200 HP

• Manufacturer: Buss

Used 100mm Buss kneader with 9/1 L/D barrel. Driven by 200 hp DC motor, includes 5.94/1 gearbox, jacketed barrel and clam shell barrel opening. Includes operator control panel. Kneader will discharge into approxi...

GALA 403VDW

• Manufacturer: GALA

Used 50,000 Lb. Per Hour Gala Model 403VDW Stainless Steel Spin Dryer 43" diameter circular housing 20 hp Baldor motor Serial No. 911039-2

AIR KNIFE 6"

• Manufacturer: AIR KNIFE

Used 6" Wide Air Knife With 2 HP Blower

Cincinnati CMT80L-APC

• Manufacturer: Cincinnati
• Model: CMT

Used Cincinnati model CMT80L-APC conical counter rotating twin screw plastic extruder. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adaptor plate that reduces the barrel exit down...

BATTENFELD-CINCINNATI CM55

• Manufacturer: Battenfeld-Cincinnati

Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...

FARRIS 8550F

• Manufacturer: Farris

Used Farris 12" Wide x 30" Long Solid Belt Puller Manufacturer: Farris Model: 8550F Has manual belt adjustment, and variable speed transmission Rated 3-50 feet per minute

GOODMAN 3" Wide x 22" Long

• Manufacturer: GOODMAN

Used Goodman Solid Belt Puller – Approx. 3" (76 mm) Wide x 22" (559 mm) Long Solid belt design with an approximate belt width of 3 inches (76 mm) and length of 22 inches (559 mm). Frame includes a provision for i...

GALA 16.2ECLN-BF

• Manufacturer: GALA

Used Gala Stainless Steel Spin Dryer Model 16.2ECLN-BF Serial #982157

AMERICAN MAPLAN V2-125-V/2L

• Manufacturer: Maplan

Used Battenfeld vacuum/cooling tank. Type V2-125-V/2L, serial #83-4058-67-01. Has 14" x 14" cross section x 18' long chamber with 10" opening. Includes (1) vacuum pump and (2) water pumps. (1) vacuum pump missing...

RANDCASTLE Ø51 мм × 203 мм

• Manufacturer: RANDCASTLE

Used 2" O.D. x 8" Wide Randcastle Sheet Extrusion 3-Roll Stack including Pull Roll Station and Single Position Winder.