Used processing

2000 DAVIS STANDARD 5.11"

• Manufacturer: Davis-Standard

Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...

2008 COPERION ZSK-40-MEGA

• Manufacturer: Coperion Waeschle

Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...

2004 SAKAS

• Manufacturer: SAKAS

Used 36" Wide Sakas Traveling Cut Off Saw Including 42" Wide Belt Take-Away. New 2004. Saw Model GS36.

MARSHALL & WILLIAMS CO-EX SHEET EXTRUSION LINE

• Manufacturer: Marshall

Used Marshall & Williams Co-Ex Sheet Extrusion Line Consisting of the Following: 2.5" Welex 36/1 L/D with air cooled vented barrel, with 9.145/1 gearbox ratio including manual screen changer, water cooled screw a...

4.5" Hydraulic Screen Changer With Pump

Used 4.5" Hydraulic Screen Changer hydraulic pump and stand. Missing breaker plates. Includes approx. 11" wide strand die without die plate. Last used on 4.5" Prodex extruder.

2001 DAVIS STANDARD PEDESTAL

• Manufacturer: Davis-Standard
• Model: PEDESTAL

Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...

Conair D400H

• Manufacturer: Conair
• Model: D400H

Used Conair model D400H high heat desiccant dryer, 300 cfm. Have carousel desiccant cartridges, operator controls, no hopper. Previously used with 900-1000 lb hopper.

POLYCOOL XCHANGER INC. 4.5"

• Manufacturer: XChanger

Used Polycool previously used on 4.5" blown film line. Separately available is 20 HP AC motor with inverter, previously used with above.

ALLIED DIES, INC. 20"

• Manufacturer: Allied

Used 20" Allied Dies Inc dual manifold sheet die. With 2" back center fed main entrance. 240 volts, 1PH, 9 zones. 3" X 0" naked edge, .060" lip opening. Last used for PVC siding. Rebuilt by Allied Dies Inc in Apr...

RUBBER ROLL 60" WIDE X 8" DIA.

• Manufacturer: RUBBER ROLL

Used 55" wide X 8" diameter rubber roll previously used as pull roll on sheet extrusion line.

NEW YORK 208

• Manufacturer: NEW YORK

Used New York Blower (3) model 208 aluminum pressure blowers, each with 10 HP. Includes polycool unit.

1997 Piovan T1000IX

• Manufacturer: Piovan

Used 1000 liter Piovan stainless steel drying hopper. New 1997. Hopper model T1000IX. Hoppers are approximately 36" diameter X 8' tall.

ZUMBACH KW20

• Manufacturer: Zumbach
• Model: KW20

Used Zumbach model KW20 surface fault detector.

ZUMBACH KW20

• Manufacturer: Zumbach
• Model: KW20

Used Zumbach model KW20 surface fault detector.

ZUMBACH KW20

• Manufacturer: Zumbach
• Model: KW20

Used Zumbach model KW20 surface fault detector.