Used processing

TRENDLEKAMP 8″ CONTINUOUS SCREEN CHANGER 18303

One used Trendlekamp model TASK8.1 dual bolt 8″ continuous screen changer. Includes support stand and hydraulic pumping unit. Manufactured in 2004

GLOUCESTER SHEET STACKER 18229

One (1) used Gloucester cut sheet stacking system. Package consists of a nominal 72″ wide x 9′ long belt conveyor with 72″ wide pneumatic sheet stacker. Last used on the end of an HDPE sheet extrusion line. ¾ hp ...

ZENITH 10 HP MELT PUMP 18234

• Manufacturer: Zenith

Zenith model 60-20000-24-2410-4 melt pump. S/N 250603. 10 HP 230/460-volt pump motor. 1 to 70.26 RPM speed range. 3/4″ entry and 2″ entry

GLOUCESTER 66″ COOLING ROLL STAND 18226

One (1) used 66″ Gloucester cooling and polishing stand having three (3) nominal 20″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation at a 56″ center-line height. Includes t...

KILLION KN-150 1.5″ 30:1 L/D 18111

One used Killion model KN-150 1.5″ 30:1 extruder. S/N 15437. Five (5) zone electrically heated, air cooled, and top-vented barrel at an approximate 39″ centerline height. Gearbox is a Koellmann model PEZS20 and h...

PRODEX 4.5″ 32:1 L/D EXTRUDER 18180

One (1) used Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear type gearbox and is direct driven in a tuck under ...

NRM PACEMAKER III 3.5″ 32:1 18061

One (1) used NRM PM III 3.5″ 32:1 L/D extruder having a five (5) zone electrically heated, air cooled, and non-vented barrel at an approximate 42″ center line height. Gearbox has a reduction ratio of 17.42:1 and ...

EGAN 6″ 30:1 L/D 400 18037

• Manufacturer: Egan

One (1) used Egan 6″ 30:1 L/D extruder. S/N 37910. Having an electrically heated, water cooled (closed loop), and vented barrel at an approximate a 42” center line height. Water system is incomplete. Philadelphi...

GNEUSS SFX75 3″ CONTINUOUS SCREEN 17999

Gneuss model SFX75 3″ continuous screen changer. S/N. 02083047. 460/3/60 operation. Includes PLC control panel

EDI 96″ SHEET DIE 17968

• Manufacturer: EDI

One (1) used sheet die believed to have been manufactured by Extrusion Dies Inc. Having a 96″ slot opening. Integral upper flexible lip and removable lower lip. Vertical restriction bar. Adjusting bolts on 1″ cen...

EDI ULTRA-FLEX R75 SHEET DIE 17969

• Manufacturer: EDI

One (1) used Extrusion Dies Inc. model Ultra-flex R75 sheet die having a 54″ slot opening. Integral upper flexible lip and removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers.. 1 ½” back...

2.5″ 30:1 L/D EXTRUDER 17759

Unknown manufacture 2.5″ extruder, 30:1 L/D air cooled non-vented barrel at a 23.5″ centerline. Powered by a 40 HP 230/460-volt A/C motor with Teco A510 inverter. 4″ x 6″ feed throat. Unitized control panel with ...

WAYNE MFG 3/4″ EXTRUDER 17885

• Manufacturer: Wayne

One used 3/4″ 20:1 L/D Wayne laboratory extruder having a two (2) zone electrically heated, air cooled barrel. Gearbox is belt driven by a 2 HP DC Motor with controls. Unitized temperature control panel with thre...

30 HP MELT PUMP 17809

30 HP 500-volt 1750/2300 RPM D/C melt pump, SM-Cyclo gearobx model CHH-4190. 2:1 gear ration with an input RPM of 45.1, 31,600 IN LBS torque, Includes Saftronics 480-volt input DC6 series drive.

GLOUCESTER 2.5″ 32:1 L/D EXTRUDER 17690

Gloucester 2.5″ extruder, 32:1 L/D five (5) zone air cooled and vented barrel at a 45″ centerline height. Top center feed throat. Driven by a 50 HP A/C 1750/2100 RPM motor, includes 6 zone temperature control pan...