Used Machining Centers in Germany

2006 Microcut VM 1000

• Manufacturer: Microcut
• Model: VM1000
• Spindle taper: SK 40
• Power requirement: 15 kilowatt

Equipment: -Cooling device with feed to the spindle (no CTS cooling through spindle)) -operating panel with manual control unit -chip conveyor -E-cabinet cooling Rittal SK 3305500

2007 ALZMETALL CS1200/3

• Manufacturer: Alzmetall
• Spindle taper: SK 40
• Power requirement: 13 kilowatt

Main spindle: Spindle head DIN 69871, SK 40/DIN 69 871-A40 and pull stud DIN 69872 Drive technology via ball screw drive Equipment: Compact filter/coolant high-pressure system Knoll Chip conveyor/scraper belt con...

2024 MAZAK INTEGREX i 100 HS

• Manufacturer: Mazak
• Model: INTEGREX I-100

Control: Mazatrol Smooth AI 5-axis simultaneous machining | Max. turning diameter: 600 mm | Max. turning length: 850 mm | Traverse: X-axis: 535 mm Y-axis: 210 mm Z-axis: 900 mm B-axis: -30 to 210° | Main spindle...

2016 MAZAK INTEGREX i 300 ST

• Manufacturer: Mazak
• Model: INTEGREX I-300ST

Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.519 mm | Traverse: X-axis: 615 mm Y-axis: 250 mm Z-axis: 1,585 mm W-axis: 1,574 mm B-axis -30 to ...

2017 MAZAK INTEGREX i-300ST

• Manufacturer: Mazak
• Model: INTEGREX I-300ST

Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.519 mm | Traverse: X-axis: 615 mm Y-axis: 250 mm Z-axis: 1,585 mm W-axis: 1,574 mm B-axis -30 to ...

RÖHM UH 3

• Manufacturer: Röhm

Additional Barely used and very well-preserved machine vise on a rotating plate Accessories Smooth clamping jaws

HILMA (wahrscheinlich) PWO-001896

• Manufacturer: Hilma

Add-on Used hydraulic machine vice on a rotating plate Accessories Smooth clamping jaws

HILMA (wahrscheinlich) SM 160

• Manufacturer: Hilma

Add-on Used hydraulic machine vice, on a rotating plate Accessories Pull-down clamping jaws No. 372204

1979 ALLMATIC 125

• Manufacturer: ALLMATIC

Add-on Little-used and very well-preserved mechanical high-pressure machine vice, pneumatically operated (instead of a hand crank) Accessories Built-in rotating plate, two longitudinal support surfaces for securi...

2017 MAZAK INTEGREX i-200S

• Manufacturer: Mazak
• Model: INTEGREX I-200 S

Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.011 mm | Traverse: X-axis: 615 mm Y-axis: 260 mm Z-axis: 1,077 mm B-axis: -30 to 210° | Rapid tra...

T-slot plate

Addition Used T-slot plate with flange ribbing on the base Further information Surface clean and flat, T-slots without breakouts, 4 flange pockets, 3 mounting holes, 2 alignment holes.

2008 HYUNDAI KIA MACHINE HS500

• Manufacturer: Hyundai
• Model: HS500

HYUNDAI KIA MACHINE HS500 2008

Foundation or clamping plates, approx. 50 pieces in stock

Additional information Approx. 50 used gray cast iron foundation or clamping plates, ribbed, with the design and T-slot layout as shown. Further information Surface clean and flat, sides machined all around (for ...

Hyundai SPT-V100

• Manufacturer: Hyundai
• Model: SPT-V100
• Power requirement: 30 kilowatt

other technical characteristics: max. drill Ø 40mm Facing 245 cc/min (cc/min) Thread cutting up to M 36 Compressed air connection Equipment: Chip conveyor with cooling water tank Interior lighting Operation via s...

2010 MAZAK INTEGREX i-150

• Manufacturer: Mazak
• Model: INTEGREX I-150

Control: Mazatrol Matrix 5-axis simultaneous machining | Max. turning diameter: 340 mm | Max. swing diameter: 400 mm | Max. turning length: 385 mm | Traverse: X/Y/Z/W: 370/200/435/300 mm B: -10° to +190° (0.0001...