Used dcs

Trusted Seller
Reifenhauser FAV 120/68
- used
- Manufacturer: Reifenhäuser
Used 47" wide Reifenhauser nip roll assembly. Type FAV 120/68, . 0263/68, Mach. No. 670. Has 8" diameter rubber/metal rolls with air actuated cylinder, Driven by a 3/4 HP, 90 arm volts DC drive.
Hainesport, NJ
Trusted Seller
1995 HPM TMIII
- used
- Manufacturer: HPM
- Model: TMIII
Used 4.5” HPM Single Screw Extruder 30/1 L/D Model: TMIII Year: 1995 6" x 6" top center feed throat Driven by a 250 hp DC motor, 460 volt AC input and a Powertec motor control with 460 volt 50/60 Hz AC input. Gea...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 48"
- used
- Manufacturer: Davis-Standard
Used Davis Standard sheet take-off unit consisting of (3) 48" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter. Top roll is tungsten and the middle a...
Hainesport, NJ
Werner & Pfleiderer ZSK40 Twin Screw Extruder for Sale – 40mm, 50 HP
- used
- Manufacturer: WP
- Model: ZSK40
10151368 Used Werner & Pfleiderer Model ZSK40, 40mm Co-rotating twin screw extruder. 1990 Model year. 46:1 L/D vented barrel with 11-barrel sections and a 41" centerline height. Driven by 50 hp 500 volt 1750/2100...
Belvidere, IL
DAVIS STANDARD 3.5″ 30:1 L/D 16399
- used
- Manufacturer: Davis-Standard
Used Davis Standard model MV35IN35SR, 3.5″ extruder, S/N K2187, SO# 99878. 30:1 L/D barrel having a seven zone electrically heated and water cooled (closed loop) and side vented barrel at a 52″ centerline height....
Elk Grove Village, IL
DAVIS STANDARD 15INDS20 1.5″ EXTRUDER 12754
- used
- Manufacturer: Davis-Standard
Davis standard model 15INDS20 1.5″ extruder S/N K-9754. SO# 02359. 24:1 L/D. Powered by a fan cooled 15 HP 500-Volt 1750/2300 RPM DC motor through a 6.53:1 gearbox 152 RPM screw speed. Electrically heated and fan...
Elk Grove Village, IL
Trusted Seller
1991 DAVIS STANDARD 100MM35F
- used
- Manufacturer: Davis-Standard
- Model: 100MM35F
Used 100mm Davis Standard 30/1 L/D non-vented Extruder. Model 100MM35F, Serial #M3027, new 12/1991. Has barrel, electrically heated, water cooled barrel. Driven by a 125 HP Reliance DC motor but no SCR control. G...
Hainesport, NJ
6″ Davis Standard 30:1 Profile Extrusion Line
- used
- Manufacturer: Davis-Standard
6″ Davis Std. 30:1 Profile Extrusion Line 30:1 L/D Two-Stage Feed Screw: Replaced in 2012 250hp. DC Motor: Rebuild in 2012 Emerson DC Drive: Rebuild in 2012 Colourmate Additive Feeder: New in 2012 Gd Nash Vacuum ...
Rockville Centre, NY
Pre-Owned Killion KL-075 Single Screw Extruder – Electrically Heated, Air-Cooled
- used
- Manufacturer: KillionKillion
54037006 Used Killion KL-075 Single Screw Extruder. 19.1 mm Diameter screws. 25:1 L/D. Screw speed 12-120 RPM via a gearbox by a 1.1 kW-380 volt/50cycle/3Ph DC motor. 3 housing sections. Electrically heated, air ...
Belvidere, IL
Trusted Seller
TEC Model 200HE 2″ Plastic Extruder
- used
TEC Model 200HE 2″ Plastic Extruder Drive- 20 horse power DC Motor with Digital Drive Additional features- – Quantum III Digital Drive – New Control panel – Digital temperature controller – 4 zones on barrel, 3 f...
Harvey, LA
Trusted Seller
Extruder 38.1 mm (1.5 in) Aluminum - IPP# 78337
- used
- Manufacturer: Sterling
Sterling Having 3-zone electrically heated water cooled non-vented Xaloy 306 lined barrel. Barrel water cooling system utilizes cast aluminum heaters in a closed loop system including reservoir pump and heat exch...
Princeton Junction, NJ
WELEX 3.5″ 30:1 L/D 150 17954
- used
- Manufacturer: Welex
One (1) used Welex 3.5″ 30:1 L/D extruder. Electrically heated water cooled (closed loop) and vented barrel at an approximate 69″ center line height. Center line height can be reduced approximately 8″ by removing...
Elk Grove Village, IL
AMERICAN MAPLAN DSK 62 EXTRUSION LINES (2) ALL DOWNSTREAM
- used
- Manufacturer: Maplan
AMERICAN MAPLAN DSK 62 EXTRUDER – MODEL DSK 62 – DC – 1987 (TWO AVAILABLE) DOWNSTREAM: CALIBATING TABLE – ACTUAL DOWNSTEAM 4 meter – MODEL AKT4 – AC – 1987 (TWO AVAILABLE) DOWNSTREAM: PULLER/SAW – ACTUAL PULLER...
Rockville Centre, NY
Trusted Seller
120mm Welex single screw extruder 30/1D Electrically heated and watrer cooled. 225kw dc motor. 190rpm screw speed. Hydraulic screen changer, gear pump.
- used
- Manufacturer: Welex
120mm Welex single screw extruder 30/1D Electrically heated and watrer cooled. 225kw dc motor. 190rpm screw speed. Hydraulic screen changer, gear pump. 115mm Welex main extruder. 30:1 l/d. Vented. Electrically he...
Swindon, United Kingdom
Trusted Seller
.75" Youngstown Little Mike Extruder, 20:1 L/D, 1 HP
- used
- Manufacturer: Youngstown
Used 3/4" Youngstown Extruder 1 HP Baldor DC Motor With DC Drive Cal 9400 Temperature Controllers 2 Barrel Zones, 2 Die Zones 230V New In 2004
United States