Processing » Kansas

Search By Category

Search By Manufacturer

Building Filters

375

Used controller in Kansas, USA

  • LS Industries - Floor Blaster

    LS Industries - Floor Blaster - LSFB-10

    • Manufacturer: LS Industries

    The LSFB-10 is a walk behind system that allows the media to strike the surface and rebounds along with removed contaminants into a recovery chamber. Features: - High performance, airless centrifugal wheel for ...

    Wichita, KS
  • LS Industries - Pipe Blaster

    LS Industries - Pipe Blaster - ID-PB2.375-7

    • Manufacturer: LS Industries

    The LS ID Pipe Blaster 2.375-7 is a 6-lance system that will blast the internal surface of up to 6 pipes at one time with a diameter of 2.375” to 7”. Features: - The 6 lances are mounted on a mechanically drive...

    Wichita, KS
  • LS Industries - Manual Blast

    LS Industries - Manual Blast Cabinet - GB601

    • Manufacturer: LS Industries

    GB601 is designed to remove rust, carbon, corrosion, paint, and scale from any surface without distorting the base metal or affecting dimensional tolerances. Features: - Finger-tip control of blow-off hose - 16...

    Wichita, KS
  • Trusted Seller
    Centrifuge, Disc, Auto, Westfalia, SAOOM

    Centrifuge, Disc, Auto, Westfalia, SAOOM 3016, S/st, #A742114

    • Manufacturer: GEA
    • Model: SAOOM 3016

    Self-cleaning Disc Stack Centrifuge, manufactured by Westfalia, model SAOOM 3016. Unit includes Allen-Bradley "Soft Start" controller as well as all tools. Mounted on frame with casters.. Previously used in pilot...

    Wichita, KS
  • Trusted Seller
    BUCKEYE BOILER HORIZONTAL AIR COMPRESSOR

    BUCKEYE BOILER HORIZONTAL AIR COMPRESSOR 4131, 30 GALLON, 1/3HP, 1PH

    • Manufacturer: Buckeye

    BUCKEYE BOILER HORIZONTAL AIR COMPRESSOR 4131, 30 GALLON, 1/3HP, 1PH BUCKEYE BOILER CO.HORIZONTAL AIR COMPRESSORP/N 4131NAT'L BD NO. 127176WP 165TEMP 450 DEGREESHEADS .119SHELL .124HEAD RADIUS EYEAR 19772 GOULD C...

    $700 USD
    Coffeyville, KS
  • Trusted Seller
    EATON HYDRAULIC TANK W/BALDOR INDUSTRIAL

    EATON HYDRAULIC TANK W/BALDOR INDUSTRIAL MOTOR CM4314T

    • Manufacturer: Eaton

    “NOT TESTED” EATON HYDRAULIC TANK TANK DIMENSIONS 72" X 35-3/4" X 21-1/4" BALDOR RELIANCE 3 PHASE MOTOR CM4314T HP: 60 VOLTS: 230/460 AMPS: 142/71 RPM: 1775 FRAME: 364TC HZ: 60 SCE ENCLOSED INDUSTRIAL CONTROL PAN...

    $5,000 USD

    Get financing

    Est. $98/mo

    Coffeyville, KS
  • Winona Van Norman - Rod

    Winona Van Norman - Rod Heater - RHX

    • Manufacturer: Norman

    Winona Van Norman's RHX was designed to assemble press fit piston pins with minimum effort to help eliminate scoring of parts during assembly. The uniformed controlled heat provided by the RHX expands the pin end...

    $972 USD
    Wichita, KS
  • LS Industries - Rubber Belt

    LS Industries - Rubber Belt Tumbler Blaster - 6-RTB

    • Manufacturer: LS Industries

    The RTB-6 is designed to clean parts with abrasive shot while gently tumbling the parts to ensure no damage. Features: - Side air wash - Shot hopper with high/low shot sensor - Small operating footprint - Conti...

    Wichita, KS
  • LS Industries - Rubber Belt

    LS Industries - Rubber Belt Tumbler Blaster - 12-RTB

    • Manufacturer: LS Industries

    The RTB-12 is designed to clean parts with abrasive shot while gently tumbling the parts to ensure no damage. Features: - Side air wash - Shot hopper with high/low shot sensor - Small operating footprint - Cont...

    Wichita, KS
  • LS Industries - Rubber Belt

    LS Industries - Rubber Belt Tumbler Blaster - 24-RTB

    • Manufacturer: LS Industries

    The RTB-24 is designed to clean parts with abrasive shot while gently tumbling the parts to ensure no damage. Features: - Side air wash - Shot hopper with high/low shot sensor - Small operating footprint - Cont...

    Wichita, KS
  • LS Industries - Rubber Belt

    LS Industries - Rubber Belt Tumbler Blaster - 3-RTB

    • Manufacturer: LS Industries

    The RTB-3 is designed to clean parts with abrasive shot while gently tumbling the parts to ensure no damage. Features: - Side air wash - Shot hopper with high/low shot sensor - Small operating footprint - Conti...

    Wichita, KS
  • LS Industries - Burn-Off Oven

    LS Industries - Burn-Off Oven - 36-SBNG

    • Manufacturer: LS Industries

    The 36-SBNG Burn-Off Oven is for removing powder coating. Features: - Cleans heads, blocks, small parts, and metal components - Total temperature and time control will ensure dry stable parts - Complete hands-f...

    Wichita, KS
  • LS Industries - Rubber Tumbler

    LS Industries - Rubber Tumbler Belt Blaster - 1.25-RTB

    • Manufacturer: LS Industries

    The RTB-1.25 is designed to clean parts with abrasive shot while gently tumbling the parts to ensure no damage. Features: - Side air wash - Shot hopper with high/low shot sensor - Small operating footprint - Co...

    Wichita, KS
  • Trusted Seller
    Blow Molder, Eceng, Plastic Bottles,

    Blow Molder, Eceng, Plastic Bottles, 1000 Bottles/hr, #A742106

    • Manufacturer: Eceng

    Plastic Blow Molder, manufactured by Eceng Machine. Unit can be used from 2-Cavity to 6-Cavity with a capacity of up to 1,000 500ml bottles/hr. Can produce up to 2L bottles. Complete with PLC control panel.. Prev...

    Wichita, KS
89101112

Overview

Processing equipment encompasses a wide range of machinery used in various industries to transform raw materials into finished products. This category includes machines like grinders, mixers, blenders, and specialized equipment for food, chemical, pharmaceutical, and other manufacturing processes. These machines are essential for improving efficiency, consistency, and quality in production lines.

FAQ

What should I consider when buying used processing equipment?

Consider the machine's condition, age, maintenance history, and whether it meets your specific processing requirements. It's also important to check for any signs of wear and ensure compatibility with your existing systems.

How do I arrange shipping for processing equipment?

Use a reliable transport service experienced in handling industrial machinery. Ensure the equipment is properly cleaned, secured, and protected during transit to avoid any damage.

What is the typical maintenance for processing equipment?

Regular maintenance includes cleaning, lubrication, inspection for wear and tear, and calibration. Follow the manufacturer's guidelines for specific maintenance schedules and procedures to ensure optimal performance and longevity.