Industrial Automation » Sensors » Flow Sensors

Building Filters

305

Used Flow Sensors

  • CR300 common rail injector test

    CR300 common rail injector test bench

      CR300 common rail injector test bench is our latest indepentent researched special device to test the performance of high-pressure common rail injector, controlled by industrial computer, Windows operating system...

      Taian, China
    • CR926/CR926S test bench

      CR926/CR926S test bench

        CR926 are 11kw motor inside, controlled by industrial computer, Windows operate system. Injector quantity and pump flow measured by flow sensor, 0- 2400bar pressure, all data can be searched and saved, Manual/aut...

        Taian, China
      • CRS708/CRS718 test bench

        CRS708/CRS718 test bench

          CRS708/CRS718 all are 11kw motor inside, controlled by industrial computer, Windows operate system. Injector quantity and pump flow measured by flow sensor, 0- 2400bar pressure, all data can be searched and saved...

          Taian, China
        • no-image_en.png

          MFM 2021 flow sensor with Tecnosens PID

          • Manufacturer: Tecnosens

          The MFM 2021 Gas Flow Sensor possesses not only MEMS technology for flow measurement but also a high-precision PID controller with analog output, which enables direct, simple, accurate and fast control of gas flo...

          Brescia, Italy
        • DANFOSS MASS 3000 MASSFLO FLOWMETER

          DANFOSS MASS 3000 MASSFLO FLOWMETER – Missing Back Cover

          • Manufacturer: Danfoss
          • Model: MASS

          USED DANFOSS MASS 3000 MASSFLO FLOWMETER – Missing Back Cover “ MISSING BACK COVER, BROKEN PART/RUSTY CASE AS SHOWN IN THE PHOTO. ”

          $810 USD
          Ajman, United Arab Emirates
        • no-image_en.png

          Combo Pack, ProFLOW6000 and Leak Detector, ea.

            Böckten, Switzerland
          • no-image_en.png

            Leak Detector VI Kit

              Böckten, Switzerland
            • no-image_en.png

              BGB Electronic Leak Detector, ea.

                Detects a broad range of gases.Audible tone and LED display indicate the severity of a leak.Can be operated during charging or used up to 12 hours between charges.Ergonomic, handheld design.Rugged side grips for ...

                Böckten, Switzerland
              • no-image_en.png

                ProFLOW 6000 Electronic Flowmeter, ea.

                  Böckten, Switzerland
                • BE-220FSD

                  BE-220FSD

                  • Manufacturer: HORIBA, Ltd.

                  OEM gas (NO) analyzer The BE-220FDS is an OEM NDIR detector for measuring NO in automotive emission gases. The BE-220FSD can output NO concentration by digital data and analog voltage. In addition, it can be conn...

                  Kyoto, Japan
                • PLR-RT series catalytic reaction evaluation

                  PLR-RT series catalytic reaction evaluation device

                  • Manufacturer: Perfectlight

                  Chemical reactions are primarily activated by heating, providing the energy to overcome thermodynamic barriers and drive the transformation of reactants into products. chemical reaction pathways, and reduce the a...

                  Beijing, China
                • MIC600-P4 Fixed Multi Gas Monitor

                  MIC600-P4 Fixed Multi Gas Monitor

                    MIC600-P4 gas monitor real-time storage and fixed time storage are supported, or only the data of the alarm concentration will be stored; it is supported to use the local host to view, and delete data, and upload...

                    Beijing, China
                  • IFM VS3000 EVALUATION SYSTEM FOR

                    IFM VS3000 EVALUATION SYSTEM FOR FLOW SENSOR

                      IFM VS3000 EVALUATION SYSTEM FOR FLOW SENSOR Voltage: 90 … 240 VA / 25 VDC Frequency: 47 … 63 Hz Power Consumption: 4 VA Current Consumption: 90 Ma Operating Temperature: -20 … 60 °C Output Status Indication: LED...

                      Bhavnagar, India
                    • Dual Pressure Methods Vacuum Decay

                      Dual Pressure Methods Vacuum Decay Leak Detection Tester AUTO GBM-L2

                        Introduction AUTO GBM-L2 Dual-Pressure Methods Vacuum Decay Leak Detection Tester adopts the test principle of vacuum decay method/pressure decay to detect micro-leakage of finished packaging. It can be applied t...

                        Guangzhou, China
                      • In Stock Invasive ICU Ventilators

                        In Stock Invasive ICU Ventilators with Compressor VG70

                          Superior Mobile ICU ventilator VG70• Comprehensive ICU ventilator including BIVENT and PRVC• Compact, big capacity battery, no air compressor, intra-hospital mobility• Flexible device configuration: equipped on a...

                          Guangzhou, China
                        1718192021

                        Overview

                        Flow sensors are devices used to measure the flow rate of liquids or gases within a pipe or system. They are crucial in various industries, including water treatment, manufacturing, and HVAC, for ensuring proper fluid flow and system efficiency. Flow sensors come in different types, such as turbine, ultrasonic, and electromagnetic, each suitable for specific applications and fluid types.

                        FAQ

                        What factors should I consider when purchasing a flow sensor?

                        Consider the type of fluid, flow rate range, accuracy requirements, and compatibility with your system. Also, check the sensor’s maintenance needs and durability in your operating environment.

                        How can I ensure my flow sensor is shipped safely?

                        Use a reputable shipping service that specializes in delicate instruments. Ensure the sensor is securely packed with protective materials to prevent damage during transit.

                        What maintenance is required for flow sensors?

                        Regular maintenance includes cleaning the sensor to prevent buildup, calibrating it periodically for accuracy, and inspecting for any wear or damage. Follow the manufacturer’s guidelines for specific maintenance procedures.