Machine Tools » Sheet Metal Processing » Switzerland

Building Filters

111

Used Sheet Metal Processing in Switzerland

  • Trusted Seller
    1971 PLATARG 611 Ref No:

    1971 PLATARG 611 Ref No: 41435

    • Manufacturer: PLATARG

    Platarg transfer press 611 Specifications: Number of stations: 12 (11+1) Capacity per ram: 6 tons Maximum stroke: 114 mm Max. shell height: 50 mm Standard ram pitch: 82 mm Blank diameter: 80 mm

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    1987 PLATARG 912 Ref No:

    1987 PLATARG 912 Ref No: 46450

    • Manufacturer: PLATARG

    The press is now in storage - was in a full running state when taken out of service. High lift stroke cams 159 mm - max. shell height 76 mm 13 Stations, 12 Rams + 1 Slave Wedge Adjustable Rams with Standard Male ...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    1996 PLATARG 2513 Ref No:

    1996 PLATARG 2513 Ref No: 46301

    • Manufacturer: PLATARG

    Can be tested in operation Max. Flywheel speed: 760 1/min. Capacity on one stage approx. 25T Clutch engagement max. 10/min Air pressure 5.5 bar (min) - 5.8 bar (max) Total deceleration time Braking <250 ms Zig...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    1977 PLATARG 611 Ref No:

    1977 PLATARG 611 Ref No: 43685

    • Manufacturer: PLATARG

    A new electrical control system and a mechanical and lubrication rebuild are required. One used PLATARG model 611 transfer press, high speed type. Full follow cams. Number of stations: 12 Number of rams: 11 + 1 s...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    1969 PLATARG 312 Ref No:

    1969 PLATARG 312 Ref No: 40583

    • Manufacturer: PLATARG

    This machine can have the following installed/added to it (not included) o new lubrication o new electrical installation o new protections o CE conformity Number of station 13 (12+1). Capacity on any one station ...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2005 ARKU RM 50X/9 ECOPLAN

    2005 ARKU RM 50X/9 ECOPLAN Ref No: 46236

    • Manufacturer: Arku

    Cut-To-Length line consisting of: - Coil loading chair HUBTEX - ARKU single-sided decoiler - ARKU VRM 5050/9 feed straightening machine, +- 0.1 mm feeding precision - measuring wheel to verify feed length - Cut-t...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2002 MIOS T-55 TR Ref

    2002 MIOS T-55 TR Ref No: 55215

    • Manufacturer: Mios

    Object: 55215 | Drive system: eccentric / crank | Total force (nominal): 55 to | Table surface (left-right): 400 mm | Table surface (front-back): 300 mm | Spigot hole diameter: 45 mm | Stroke: 50 mm | Strok...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2001 MIOS T20 FV Ref

    2001 MIOS T20 FV Ref No: 55890

    • Manufacturer: Mios

    Object: 55890 | Drive system: eccentric / crank | Openings in uprights: yes | Number of slide actions: 1 | Table cushion: no | Quick die change system: no | Total force (nominal): 20 to | Spigot hole diameter: ...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2000 IMS 50 RE Ref

    2000 IMS 50 RE Ref No: 55279

    • Manufacturer: IMS

    Object: 55279 | Drive system: eccentric / crank | Total force (nominal): 50 to | Table surface (left-right): 440 mm | Table surface (front-back): 360 mm | Spigot hole diameter: 40 mm | Stroke: 90 mm | Strok...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2002 ESNA VFS/PN45 Ref No:

    2002 ESNA VFS/PN45 Ref No: 55264

    • Manufacturer: ESNA

    Object: 55264 | Drive system: eccentric / crank | Total force (nominal): 45 to | Table surface (left-right): 410 mm | Table surface (front-back): 280 mm | Opening in bed (diameter): 40 mm | Stroke rate (max....

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    1997 ROSS 63R4 Ref No:

    1997 ROSS 63R4 Ref No: 55175

    • Manufacturer: Ross

    Object: 55175 | Controls: DANFOS | Drive system: eccentric / crank | Frame design: C-frame, single sided, inclinable | Openings in uprights: yes | Number of slide actions: 1 | Table cushion: no | Opening in tabl...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2002 MIOS T20 FV Ref

    2002 MIOS T20 FV Ref No: 53991

    • Manufacturer: Mios

    Object: 53991 | Spigot hole diameter: 30 mm | Stroke rate (max.): 155 /min | Stroke min.: 5 mm | Stroke max.: 60 mm | Shut height (stroke down, adjustment up), bdc: 280 mm | Throat (c-frame): 180 mm | Tota...

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    2000 PRESSIX 100 CNR 4

    2000 PRESSIX 100 CNR 4 Ref No: 51223

    • Manufacturer: Pressix

    Located in Barcelona - Spain 2 identical units available

    Niederhelfenschwil, Switzerland
  • Trusted Seller
    GRESSEL HB 20-8

    GRESSEL HB 20-8

    • Manufacturer: Gressel

    Bending angle max: 180 Grad | Bending height max: 100 mm | Clamping range: 40 mm | Length x width x height: 420x270x210 mm | Weight approx: 45 Kg

    Beringen, Switzerland
  • Trusted Seller
    2015 Bystronic Fiber 4020 6KW

    2015 Bystronic Fiber 4020 6KW

    • Manufacturer: Bystronic

    This Bystronic Fiber 4020 6KW was manufactured in 2015. It features a tool changer for sheet metal formats up to 2030 mm x 4030 mm and a 6kW fiber laser. The operator terminal is equipped with a touchscreen, USB ...

    Switzerland
34567

Overview

Sheet metal processing involves the cutting, bending, and assembling of sheet metal to create different products and structures. This category includes machinery such as presses, shears, lasers, and CNC machines, all designed to handle various types of metal sheets for industries like automotive, aerospace, and construction.

FAQ

What should I consider when buying used sheet metal processing equipment?

Check the machine's age, condition, and maintenance history. Verify its compatibility with your specific metal types and thicknesses, as well as its operational accuracy and efficiency.

How can I ensure safe shipping of sheet metal processing equipment?

Hire a specialized heavy machinery transport service. Ensure the equipment is properly secured and protected to prevent damage during transit.

What is the maintenance schedule for sheet metal processing equipment?

Regular maintenance includes inspecting and lubricating moving parts, checking electrical systems, and cleaning to prevent dust buildup. Refer to the manufacturer's manual for specific maintenance intervals and procedures.