Category

Country

Used Walker Machine Tools

- 34 listings found
Sort by Price: Low to High | High to Low
  • Used Mitsui 200 MH Handfeed Surface Grinder

    • Manufacturer: Walker

      Used mitsui 200 mh handfeed surface grinder specifications maximum grinding chuck size 6.0” x 12.0” maximum distance under wheel to table 14.0” table load capacity w/chuck 200 lbs. maximum table travel 15.0” m...

      $8,000 (USD)
      Dousman, WI, USA
    • 300 Gal Walker Stainless Steel Pressure Vessel 9496

      • Manufacturer: Walker
      • Capacity: 300 Gal

      Used 300 gallon t304 stainless steel horizontal tank. 30" diameter x 96" straight side. dished heads. rated 15 psi/fv at 250 degrees f. 2 saddles. 4" bottom outlet. built by walker.

      No price
      Red Bank, NJ, USA
    • 70 Gal Walker Stainless Steel Pressure Vessel 9493

      • Manufacturer: Walker
      • Capacity: 70 Gal

      Used approximately 70 gallon stainless steel vertical tank. 24"" x 36"". dished top and bottom heads. jacketed bottom 12"" and bottom head. 15 psi internal. 70 psi bottom jacket. serial number 1300-7983. t 304 st...

      No price
      Red Bank, NJ, USA
    • Walker 24 X 048

      • Manufacturer: Walker

        Length of chuck .................. 72" width of chuck ................... 36-1/4" height ........................... 6-1/4"

        No price
        Holland, OH, USA
      • 12" X 48" WALKER MAGNETIC CHUCK W/ NEUTRIFER CONTROLLER

        • Manufacturer: Walker

          Make ....................... walker length of chuck ............ 48" width of chuck ............. 12" height of chuck ............ 4-3/8" controller ................. neutrifier ii serial ..................... 95...

          No price
          Holland, OH, USA
        • 20" WALKER TURNER 4 SPINDLE DRILL PRESS 14275

          • Manufacturer: Walker
          • Capacity: ( CAST IRON )

          Heads adjusted vertically by rack & crank - 20" 2 tapping heads as taken from service temporary specifications

          No price
          Des Plaines, IL, USA
        • 20" WALKER TURNER 4 SPINDLE DRILL PRESS 14298

          • Manufacturer: Walker
          • Capacity: ( STEEL )

          Manual down feed with adjustable stop drill chuck as taken from service

          No price
          Des Plaines, IL, USA
        • Kitchen & Walker E2

          • Manufacturer: Walker
          • Capacity: 45 mm

          F2782 kitchen & walker 4’ radial arm drill, type e2, serial no a286, spindle speeds 25 -1560rpm (18), spindle taper 4mt, spindle diameter 60mm, spindle feeds 0.0035 – 0.041 inch per rev (9), quill traverse 355mm,...

          No price
          United Kingdom
        • 1994 KITCHEN & WALKER KWM 80-2500 3000mm Radial Drill, No.6 Morse Taper

          • Manufacturer: Walker
          • Weight: 13.1/2 ton / 13,716 kgs

          input: 415/3/50 ac 7.5 kw | width: 1400mm | height: 3630mm | length: 4400mm | throat: 2400mm x 2200mm high | comments: ***video shows the machine under power*** | base area: 2530mm x 1400mm | feed rate: 0.035mm ...

          No price
          Leicester, United Kingdom
        • 1978 KITCHEN & WALKER E3 4'6" / 1372mm Radial Drill, No.5 Morse Taper

          • Manufacturer: Walker
          • Weight: 4 ton / 4064 kgs

          input: 380/420/3/50 ac 4 kw | width: 3'4" / 1.02m | height: 9'6" / 2.9m | length: 8' / 2.44m | throat: 41" x 50" / 1041mm x 1270mm | base area: 54" x 39.1/2" / 1372mm x 1003mm | feed rate: 0.0035" - 0.041" / 0.0...

          No price
          Leicester, United Kingdom