Processing » Extruders

Search By Manufacturer

Search By Country

Building Filters

10005

Used Extruders

  • Trusted Seller
    PRODEX 4.5"

    PRODEX 4.5"

    • Manufacturer: PRODEX

    Used 4.5" pelletizing line consisting of the following: - 4.5" Prodex 34/1 L/D vented extruder including strand die, Lufkin "Change Gear" gearbox with 15.03/1 reduction, and an hydraulic screen changer with pump....

    Hainesport, NJ
  • Trusted Seller
    DAVIS STANDARD 150INDS-20

    DAVIS STANDARD 150INDS-20

    • Manufacturer: Davis-Standard

    Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...

    Hainesport, NJ
  • Trusted Seller
    Motan 100

    Motan 100

    • Manufacturer: Motan

    Used 300 lb. Motan model 100 desiccant dryer. No hopper included. Serial #9003860. 6 kW total heater load, 80-100 psi air, 2.3 HP. 240 volt AC input.

    Hainesport, NJ
  • Trusted Seller
    1997 PIOVAN T6000ix

    1997 PIOVAN T6000ix

    • Manufacturer: Piovan

    Used 6000 lb Piovan stainless steel drying hopper. New 1997. Hopper model T6000ix. Hoppers are approximately 60" o.d. X 14' tall.

    Hainesport, NJ
  • Trusted Seller
    CINCINNATI MILACRON 34" Wide

    CINCINNATI MILACRON 34" Wide

    • Manufacturer: Cincinnati

    Used 34" wide Cincinatti Milacron 2-roll sheet take-off with 34" face X 18" diameter rolls. Rolls are mounted in a vertical stack arrangement. Chromed and cored rolls with rotary unions, silent chain driven with ...

    Hainesport, NJ
  • Trusted Seller
    THORESON MCCOSH TD360

    THORESON MCCOSH TD360

    • Manufacturer: Thoreson McCosh

    Used Thoreson McCosh Model TD360 desiccant dryer including approximately 1000 lb. hopper. Rated at approximately 360 lbs. per hour. Includes 10 hp 460 volt motor, Serial #971128.

    Hainesport, NJ
  • Trusted Seller
    THORESON MCCOSH TD-24

    THORESON MCCOSH TD-24

    • Manufacturer: Thoreson McCosh

    Used Thoreson McCosh Model TD-24 dehumidifying hopper dryer. Serial #206-152-10. Caster mounted dryer includes 50 lb. capacity insulated hopper mounted on stand. 24 CFM. 480 volt, 3 phase, 60 cycle operation at 9...

    Hainesport, NJ
  • Trusted Seller
    NOVATEC CDM-750

    NOVATEC CDM-750

    • Manufacturer: Novatec
    • Model: CDM-750

    Used Novatec Desiccant Dryer. Model CDM-750, serial number #12-095, new 1994. Has touch screen micro processor control model MCD-1002. Includes (2) approximatey 1000 lb hoppers with receivers and process heaters....

    Hainesport, NJ
  • Trusted Seller
    JOHNSON

    JOHNSON

    • Manufacturer: Johnson

    Used Johnson roll pull roll stand Has (2) 54" x 8" diameter rubber covered rolls Rolls are driven by 10 hp DC motor Drive-All 4-speed gearbox Air actuated top pull roll

    Hainesport, NJ
  • Trusted Seller
    1991 DAVIS STANDARD 4.5"

    1991 DAVIS STANDARD 4.5"

    • Manufacturer: Davis-Standard

    Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...

    Hainesport, NJ
  • Trusted Seller
    2000 DAVIS STANDARD 5.11"

    2000 DAVIS STANDARD 5.11"

    • Manufacturer: Davis-Standard

    Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...

    Hainesport, NJ
  • Trusted Seller
    1997 DAVIS STANDARD 5.11"

    1997 DAVIS STANDARD 5.11"

    • Manufacturer: Davis-Standard

    Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...

    Hainesport, NJ
  • Trusted Seller
    1997 Piovan T1000IX

    1997 Piovan T1000IX

    • Manufacturer: Piovan

    Used 1000 liter Piovan stainless steel drying hopper. New 1997. Hopper model T1000IX. Hoppers are approximately 36" diameter X 8' tall.

    Hainesport, NJ
  • Trusted Seller
    THORESON MCCOSH TD2000

    THORESON MCCOSH TD2000

    • Manufacturer: Thoreson McCosh

    Used 6,000 lb. Thoreson McCosh Desiccant Dryer Model TD2000. Serial #201-703-05. 480 volt, AC input, 20 hp. Amps 236.0, kw 182.0. No hopper included.

    Hainesport, NJ
  • Trusted Seller
    UNA-DYN GS150

    UNA-DYN GS150

    • Manufacturer: Una-Dyn

    Used Una Dyn Piovan Desiccant Dryer. Model GS150, serial #237240-01-01-0903. Rated at 150 cfm. Includes approximately 800 LB., 30" diameter x 72" straight side x 19" cone bottom insulated hopper with top mounted ...

    Hainesport, NJ
  • Trusted Seller
    1997 Piovan T1000IX

    1997 Piovan T1000IX

    • Manufacturer: Piovan

    Used 1000 liter Piovan stainless steel drying hopper. New 1997. Hopper model T1000IX. Hoppers are approximately 36" diameter X 8' tall.

    Hainesport, NJ
2728293031

Overview

Extruders are machines used in the manufacturing process to shape materials by forcing them through a die. Commonly used in plastic and metal industries, extruders are essential for creating products like pipes, sheets, and profiles. Their versatility allows them to handle various materials, including polymers, rubber, and even food products.

FAQ

What should I consider when buying a used extruder?

Evaluate the extruder's condition, age, and previous usage. Check for signs of wear, especially on the screw and barrel, and ensure the machine has been well-maintained.

How do I ensure the extruder is shipped safely to my location?

Hire a logistics company experienced in transporting heavy machinery. Make sure the extruder is properly secured, and all parts are protected from damage during transit.

What is the maintenance schedule for an extruder?

Regular maintenance includes inspecting the screw and barrel for wear, checking and replacing filters, and ensuring the cooling and heating systems are functioning properly. Follow the manufacturer’s guidelines for specific maintenance intervals.