Processing » Extruders

Search By Manufacturer

Search By Country

Building Filters

9979

Used Extruders

  • Trusted Seller
    2008 COPERION ZSK-40-MEGA

    2008 COPERION ZSK-40-MEGA

    • Manufacturer: Coperion Waeschle

    Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...

    Hainesport, NJ
  • Trusted Seller
    WERNER & PFLEIDERER ZSK20

    WERNER & PFLEIDERER ZSK20

    • Manufacturer: WP
    • Model: ZSK20

    Used 40mm Werner & Pfleiderer co-rotating Twin Screw Extruder. Model ZSK40, serial #180399, new 1990. Has 46/1 L/D vented barrel with 11-barrel sections and a 41" centerline height. Driven by 50 hp 500 volt 1750/...

    Hainesport, NJ
  • Trusted Seller
    1997 PIOVAN T6000ix

    1997 PIOVAN T6000ix

    • Manufacturer: Piovan

    Used 6000 lb Piovan stainless steel drying hopper. New 1997. Hopper model T6000ix. Hoppers are approximately 60" o.d. X 14' tall.

    Hainesport, NJ
  • Trusted Seller
    CINCINNATI MILACRON 34" Wide

    CINCINNATI MILACRON 34" Wide

    • Manufacturer: Cincinnati

    Used 34" wide Cincinatti Milacron 2-roll sheet take-off with 34" face X 18" diameter rolls. Rolls are mounted in a vertical stack arrangement. Chromed and cored rolls with rotary unions, silent chain driven with ...

    Hainesport, NJ
  • Trusted Seller
    THORESON MCCOSH TD360

    THORESON MCCOSH TD360

    • Manufacturer: Thoreson McCosh

    Used Thoreson McCosh Model TD360 desiccant dryer including approximately 1000 lb. hopper. Rated at approximately 360 lbs. per hour. Includes 10 hp 460 volt motor, Serial #971128.

    Hainesport, NJ
  • Trusted Seller
    THORESON MCCOSH TD-24

    THORESON MCCOSH TD-24

    • Manufacturer: Thoreson McCosh

    Used Thoreson McCosh Model TD-24 dehumidifying hopper dryer. Serial #206-152-10. Caster mounted dryer includes 50 lb. capacity insulated hopper mounted on stand. 24 CFM. 480 volt, 3 phase, 60 cycle operation at 9...

    Hainesport, NJ
  • Trusted Seller
    JOHNSON

    JOHNSON

    • Manufacturer: Johnson

    Used Johnson roll pull roll stand Has (2) 54" x 8" diameter rubber covered rolls Rolls are driven by 10 hp DC motor Drive-All 4-speed gearbox Air actuated top pull roll

    Hainesport, NJ
  • Trusted Seller
    2002 LEISTRITZ ZSE 100

    2002 LEISTRITZ ZSE 100

    • Manufacturer: Leistritz

    Used Leistritz 100mm 44/1 L/D Co-Rotating Twin Screw Extruder. Model ZSE100 GL/44D, serial #3092, new 2002. Driven by 330 kw (442 hp), 1600 rpm DC motor with SCR control. Has 300 rpm screw speed, rated at 5000 Ne...

    Hainesport, NJ
  • Trusted Seller
    BATTENFELD CINCINNATI CM55

    BATTENFELD CINCINNATI CM55

    • Manufacturer: Battenfeld-Cincinnati

    Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...

    Hainesport, NJ
  • Trusted Seller
    Cincinnati CMT80L-APC

    Cincinnati CMT80L-APC

    • Manufacturer: Cincinnati
    • Model: CMT

    Used Cincinnati model CMT80L-APC conical counter rotating twin screw plastic extruder. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adaptor plate that reduces the barrel exit down...

    Hainesport, NJ
  • Trusted Seller
    Cincinnati Argos 112P-65-20-1150-UL

    Cincinnati Argos 112P-65-20-1150-UL

    • Manufacturer: Cincinnati

    Used 112mm Cincinnati model Argos 112P-65-20-1150-UL parallel counter rotating twin screw plastic extruder. Serial #2804784/010. Screw length approximately 3020mm long x 112mm diameter screw, L/D ration of 27:1. ...

    Hainesport, NJ
  • Trusted Seller
    ZUMBACH KW20

    ZUMBACH KW20

    • Manufacturer: Zumbach
    • Model: KW20

    Used Zumbach model KW20 surface fault detector.

    Hainesport, NJ
  • Trusted Seller
    ZUMBACH KW20

    ZUMBACH KW20

    • Manufacturer: Zumbach
    • Model: KW20

    Used Zumbach model KW20 surface fault detector.

    Hainesport, NJ
  • Trusted Seller
    ZUMBACH KW20

    ZUMBACH KW20

    • Manufacturer: Zumbach
    • Model: KW20

    Used Zumbach model KW20 surface fault detector.

    Hainesport, NJ
  • Trusted Seller
    ZUMBACH KW20

    ZUMBACH KW20

    • Manufacturer: Zumbach
    • Model: KW20

    Used Zumbach model KW20 surface fault detector.

    Hainesport, NJ
2829303132

Overview

Extruders are machines used in the manufacturing process to shape materials by forcing them through a die. Commonly used in plastic and metal industries, extruders are essential for creating products like pipes, sheets, and profiles. Their versatility allows them to handle various materials, including polymers, rubber, and even food products.

FAQ

What should I consider when buying a used extruder?

Evaluate the extruder's condition, age, and previous usage. Check for signs of wear, especially on the screw and barrel, and ensure the machine has been well-maintained.

How do I ensure the extruder is shipped safely to my location?

Hire a logistics company experienced in transporting heavy machinery. Make sure the extruder is properly secured, and all parts are protected from damage during transit.

What is the maintenance schedule for an extruder?

Regular maintenance includes inspecting the screw and barrel for wear, checking and replacing filters, and ensuring the cooling and heating systems are functioning properly. Follow the manufacturer’s guidelines for specific maintenance intervals.