Used Saws in Ohio, USA

1998 EISELE VMS II PV #0424322

• Manufacturer: Eisele
• Model: VMS-II

CAPACITIES: Blade diameter: 9.44" | 90 deg flat: 5.5" X 2.75" | 90 deg round: 3.14" | 45 deg flat: 3.9" X 2.75"

1982 MARVEL SERIES 8 MARK I #0950920

• Manufacturer: Marvel
• Model: 8 Mark I

FEED PRESSURE RANGE, INF VAR. 0-140 LBS. Nominal: 18" X 20" | Maximum: 18" X 22-1/2" | Blade @ 45 deg nominal: 18" X 12-1/4" | Blade @ 45 deg maximum: 18" X 13" | Table working surface: 33" X 24-1/4" | Table heig...

MOTCH & MERRYWEATHER 00-G #0288912

• Manufacturer: MOTCH & MERRYWEATHER

SPECIFICATIONS: Blade Diameter...........................: 8" - 14" Blade Speed..............................: 26 - 190 FPM Motor....................................: 2 HP Electrical Requirements....................

MOTCH & MERRYWEATHER 00-G #0288812

• Manufacturer: MOTCH & MERRYWEATHER

Blade Diameter...........................: 8" - 14" Blade Speed..............................: 26 - 190 FPM Motor....................................: 2 HP Electrical Requirements..................: 3ph, 220/440 ...

DOALL 2613-3

• Manufacturer: DoAll
• Model: 2613-3

Doall Vertical Bandsaw Variable Speed Hydraulic Feed Table Blade Welder With hydraulic table feed Doall Model AW-2 4KVA Blade Welder, grinder & shear Selector switch for off - on 3-speed transmission Electric f...

AMADA VT-5063SW #1218725

• Manufacturer: Amada

EQUIPPED WITH: WORK REST ROLLERS POWERED CLAMP UPGRADED AMADA FEED SYSTEM SEIMENS CNC TOUCH CONTROL PROGRAMMABLE CONTROL POWERED CHIP CONVEYER

MARVEL SERIES 8 MARK II #0665125

• Manufacturer: Marvel
• Model: 8 Mark II

1996 PEERLESS HB1014A #0787424

• Manufacturer: Peerless
• Model: HB1014A

EQUIPPED WITH: 48" AUTOMATIC FEED HYDRAULIC SHUTTLE W/ MULTI INDEXING AUTOMATIC WORK HEIGHT SELECTOR DUAL DOWNFEED SYSTEM

PEERLESS HB-711A #0873124

• Manufacturer: Peerless
• Model: HB-711A

Capacity: 7" X 11" | Round: 10" | Work height: 29-1/2" | Blade speed: 65,120,180,220,265 SFPM | Motor hp: 3 HP/230/460/3 PHASE

WELLS W918 #0316123

• Manufacturer: WELLS

MOTOR: 1 HP, 220/440 VOLT, 3.4/1.7 AMPS, 3 PHASE Capacity: 12" X 18" | Rpm: 1710 | Coolant: YES | Automatic elevation: YES | Pressure tilt: YES

DOALL C-57 #0628222

• Manufacturer: DoAll
• Model: C-57

CAPACITIES: EQUIPPED WITH: HYDRAULIC VISE CLAMPING

20" WELLSAW VERTICAL BANDSAW Z24032C

• Manufacturer: Wellsaw

20" THROAT 1/2" BLADE WIDTH 180" BLADE LENGTH 16" MAX WORK HEIGHT 26" X 26" TABLE WORK LIGHT TABLE TILTS VARIABLE SPEED BLADE WIRE BRUSH CLEANER 46" X 26" X 72" T APROX. 115 VOLT

18" AMADA MODEL VAC-500 BANDSAW 29014J

• Manufacturer: Amada
• Model: VAC-5000

SERIAL ......................... 530514 MODEL .......................... VAC 5000 THROAT ......................... 18´´ BLADE WIDTH RANGE .............. 1´´ BLADE LENGTH ................... 156´´ BLADE SPEEDS (VA...

PARMA ROLL-A-MATIC

• Manufacturer: PARMA

NOT HORIZ BUT VERT GRAVITY FED CUT OFF SAW Angle Plate Block 115VAC 60 Hz Single Phase Gravity Feed Metal Cutting Vertical 3/4 Hp Table Height 35 3/4" from floor Swivel angle block to CLAMP to Mfg since 1948 Roll...

DOALL C–916 #0559825

• Manufacturer: DoAll
• Model: C-916

533–97162 14-1/2" DIAMETER CAST-IRON BAND WHEELS 3-PHASE 2HP MOTOR [208V]