Used Extruders

Trusted Seller
1994 HPM 3.5TMC-24
- used
- Manufacturer: HPM
Used 3.5" 24/1 L/D HPM non-vented extruder. Model 3.5TMC-24, serial #93182. New 1994. Has electrically heated, air-cooled, barrel. Belt driven by a 75 hp brushless DC motor with controls. Flender gearbox type SZN...
Hainesport, NJ
Trusted Seller
BATTENFELD GLOUCESTER 54" Wide
- used
- Manufacturer: Battenfeld
Used 54" Wide Battenfeld Gloucester Co-Extrusion Sheet Extrusion Line, previously used for approximately 1200 lbs. per hour polypropylene sheet. Line consists of the following: (3) Acrison volumetric feeders with...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 150INDS-20
- used
- Manufacturer: Davis-Standard
Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...
Hainesport, NJ
Welex 3.5" 30:1 L/D Extruder – 150 HP, Vented Barrel, Melt Pump & Screen Changer
- used
- Manufacturer: Welex
10755146 Used Welex 3.5" 30:1 L/D Extruder. Electrically heated water cooled (closed loop) and vented barrel at an approximate 69" center line height. Center line height can be reduced approximately 8" by removin...
Belvidere, IL
Trusted Seller
1997 DAVIS STANDARD 5.11"
- used
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
2000 DAVIS STANDARD 5.11"
- used
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
1991 DAVIS STANDARD 4.5"
- used
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 1.5"
- used
- Manufacturer: Davis-Standard
- Model: 15
Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...
Hainesport, NJ
Trusted Seller
2001 DAVIS STANDARD PEDESTAL
- used
- Manufacturer: Davis-Standard
Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...
Hainesport, NJ
3.5″ NRM PM70 -24:1 N/VENTED AIR COOLED EXTRUDER
- used
- Manufacturer: NRM
Rockville Centre, NY
75mm Davis Standard “Super Blue” Extruder 24:1 – Air Cooled 2013
- used
- Manufacturer: Davis-Standard
Rockville Centre, NY
Trusted Seller
RANDCASTLE Ø19 мм, L/D 24:1
- used
- Manufacturer: RANDCASTLE
Used Randcastle Laboratory Sheet Extrusion Line Consiting of the Following Items: - .75" Randcastle 24/1 L/D extruder with temperature control panel, model RCP0750, serial #J2271. - 2" O.D. x 8" wide chill roll s...
Hainesport, NJ
Italtech Sandore Pasta Mixer Extruder – Model MX180DH | 200 kg/hr | 195mm Die | 8.5 kW | Built 2008
- used
- Manufacturer: SandoreSandore
53530001 Used Italtech Sandore Pasta Mixer Extruder, Model MX180DH. 200 Kg/hour extrusion production; 30 kg extruder basin dough capacity; 50/kg mixer/kneader basin dough capacity; 195mm die dimension; Vacon X-Se...
Belvidere, IL
Cincinnati Extruders (TC 86mm) CM 80 – CM 111(Several of each)
- used
- Manufacturer: Cincinnati
Rockville Centre, NY
Trusted Seller
Conair D400H
- used
- Manufacturer: Conair
- Model: D400H
Used Conair model D400H high heat desiccant dryer, 300 cfm. Have carousel desiccant cartridges, operator controls, no hopper. Previously used with 900-1000 lb hopper.
Hainesport, NJ