Used Materials Testing in Taiwan

Motor Twist Counter for yarn, Manual twist counter for yarn Confirm to ISO 2061 ASTM D1422 BS-903 FZ-T10001 JIS L1095 Standard

• Manufacturer: cometech testing machines

This test machine uses the characteristics of different length of yarn after twisting. Use the pointer or sensor to detect changes in the yarn to figure the twist value of the measured object. This is a very impo...

Digital Rockwell Hardness Tester Confirm to GB/T230.2, JJS Z2245, EN-ISO6508, ASTME-18 Standard

Applications: Hard alloy / Surface hardened steel / Copper alloy / Carburized steel / Hard cast steel / Malleable casting / Annealed steel / Hardened steel /Aluminum alloy / Soft steel / Bearing steel Features: ●...

QC-638 Vertical Rebound Resilience Tester Confirm to ASTM-D2632 Standard

• Manufacturer: cometech testing machines

This tester measures rubber elasticity based on free vertical drop hammer test method. The 28 gram of hammer is lifted to a height of 400mm for impact test. Average the 4th , 5th and 6th impact bound height value...

H.D.T. Heat Deflection Tester Confirm to ASTM D648 ISO 75-1 Standard

• Manufacturer: cometech testing machines

The specimen is given a stress at the center, and the temperature should increase by 2 degrees Celsius per minute. When the specimen’s center area reach the deflection of 0.254mm, the temperature is determined as...

QC-116 Digital Bursting Strength Tester Confirm to ISO-2759, GB/T 6545, JIS-P8112, JIS-L1018, ASTM-D2210, TAPPI-T403 Standard

Digital Bursting Strength Tester is used for testing the bursting resistance for samples such as base paper, corrugating paper, leather, synthetic leather. This tester is a digital type that features automatic co...

Manual Drop Dart Impact Tester Confirm to ASTM D1709 GB-9639 Standard

• Manufacturer: cometech testing machines

This tester conforms to test standard applicable for method A and method B. Clamp the plastic film on a round specimen holder (dia. 127mm). The impact head used in method A is dia. 38.1mm and in method B is dia. ...

QC-317F Digital Hydrostatic Head Tester Confirm to AATCC127, JIS- L1092, ISO811 Standard

• Manufacturer: cometech testing machines

Hydrostatic Head Tester (Hydro tester) is used for determining the water penetration resistance of high-waterproof clothingor coated fabrics by conducting the hydrostatic pressure test. It is an Open-Plan. The si...

Demattia Flex Crack Tester Confirm to ASTM-D813, JIS-K6301 Standard

• Manufacturer: cometech testing machines

QC-625 Rubber, leather, synthetic leather, sole of shoes, after a constant flexing bending motion, observe the cracking lever to judge and compare the endurance of material. Industry: Rubber, Leather, shoes sole

Manual Crock Meter Confirm to JIS-L0849, ISO-105, AATCC-8 ,JIS-L0862 Standard

• Manufacturer: cometech testing machines

This tester’s abrasion head can clamp dry or wet white cloth, under 900g loads, revolving handle by hand to proceed with specimen abrasion test (Common standard is 10 test times), test speed is around 60 CPM. Aft...

Full-Auto Rockwell Hardness Tester Confirm to GB/T230.2, JJS Z2245, EN-ISO6508, ASTME-18 Standard

Applications: Hard alloy / Surface hardened steel / Copper alloy / Carburized steel / Hard cast steel / Malleable casting / Annealed steel / Hardened steel /Aluminum alloy / Soft steel / Bearing steel Features: ●...

Pneumatic Specimen Punch

• Manufacturer: cometech testing machines

QC-603A of power is pneumatic with hand safety switch design, so there will be no security problem in operation. The tester with all kind of cutter can quickly cut out various shapes of specimen. It is suitable f...

Dyeing Rubbing Tester Confirm to JIS-L0801/L0849/L1006/ L1084/ K6328/P8136 Standard

• Manufacturer: cometech testing machines

QC-319 for textile, leather and fluff dyeing fastness test equipment. Test hammer surface can clamp dry or wet by organic solvent white cloth, abrasion head select 200g or 500g load, speed 30CPM to proceed with b...

Hardness Specimen Cutting Device

• Manufacturer: cometech testing machines

QC-603I is suitable for hardness flat shape of polymer material, as a fixed sample or specimen trimming purposes. It needs to base on forming of appearance to make mold and take slightly larger than finished prod...

Adhesion/Release Tester Confirm to FINAT 4 Standard

• Manufacturer: cometech testing machines

QC-527 test range can do low and high speed peel test and also for 90 ° 、180° multi-angle peel test. Low speed peeling force generally uses 300mm/min to proceed with test, testlow-stick adhesive label tear force....

Dropping Impact Tester Confirm to JIS-A5403, K6745 Standard

• Manufacturer: cometech testing machines

The specimen is placed on the platform of machine. Choose a designated size of steel ball to fall freely from a height, then the steel ball will impact on specimen’s surface. To observe the specimen of damaged co...