Processing » Extruders

Search By Manufacturer

Search By Country

Building Filters

9969

Used Extruders

  • Trusted Seller
    60" WIDE X 8" DIA.

    60" WIDE X 8" DIA.

    • Manufacturer: RUBBER ROLL

    Used 55" wide X 8" diameter rubber roll previously used as pull roll on sheet extrusion line.

    Hainesport, NJ
  • Trusted Seller
    1998 FUTURE DESIGN, INC. DSS1816IBC

    1998 FUTURE DESIGN, INC. DSS1816IBC

    • Manufacturer: FUTURE DESIGN, INC.

    Used 16" Future Design blown film die. Model #DSS1816IBC, new 1998. 0.050 die gap. Die is mounted on fixed cart. Has a manual screen changer and IBC. Serial #F984673.

    Hainesport, NJ
  • Trusted Seller
    DUAL LIP AIR RING 12"

    DUAL LIP AIR RING 12" DIA.

    • Manufacturer: DUAL LIP AIR RING

    Used 12" diameter dual lip air ring, 20 HP air ring blower, and Polycool.

    Hainesport, NJ
  • Trusted Seller
    EDI Autoflex R75

    EDI Autoflex R75

    • Manufacturer: EDI

    Used 60" EDI Autoflex R75 sheet die. Has 45 degree restrictor bar and removable lower lip. Center back feed. Serial #89-30122. No control for auto flex included.

    Hainesport, NJ
  • Trusted Seller
    ALLIED DIES, INC. AHM-100

    ALLIED DIES, INC. AHM-100

    • Manufacturer: Allied

    72" wide Allied "Duraflow" AHM-100 flex lip sheet extrusion die. Job #AD2763. Lip opening .001"-.100" opening. Has back center feed, 4" W X 1.753" H.

    Hainesport, NJ
  • Trusted Seller
    SUPERSAC UNLOADING STATION

    SUPERSAC UNLOADING STATION

    • Manufacturer: SUPERSAC

    Used dual Super Sack unloading station including position for (2) super sacks. Has hoist for each station, hopper unload, and operator control panel. Includes (1) volmetric feeders for discharging of each sack.

    Hainesport, NJ
  • Trusted Seller
    4.5" Crammer Feeder

    4.5" Crammer Feeder

    • Manufacturer: Egan

    Used Approximately 4.5" Diameter Egan Crammer Feeder. Including 30HP motor and motor drive. Includes spare auger.

    Hainesport, NJ
  • Trusted Seller
    NORDSON ULTRAFLEX R-75

    NORDSON ULTRAFLEX R-75

    • Manufacturer: Nordson

    Used 59" Nordson/Extrusion Dies Inc Heavy Duty Sheet Die. Model Ultraflex R-75. Serial #73-1362-2-3. Has integral upper flexible lip and fixed removable lower lip. With adjusting bolts on 1" centers, 45 degree re...

    Hainesport, NJ
  • Trusted Seller
    2008 EMERSON MENTOR

    2008 EMERSON MENTOR

    • Manufacturer: Emerson

    Used 200 HP Emerson "Mentor" SCR Controller. Has 220/480 volt input, with 268 HP rating, and output 250/530 volt. New approximately 2008.

    Hainesport, NJ
  • Trusted Seller
    IDN IDHT Gaylord

    IDN IDHT Gaylord

    • Manufacturer: IDN IDHT

    Used IDN IDHT Gaylord tilter having a 4000 lb capacity.

    Hainesport, NJ
  • Trusted Seller
    Welex 88"

    Welex 88"

    • Manufacturer: Welex

    Used Welex cast station only consisting of an 18" X 88" cast roll mounted on frame, with drive. Serial #8441. Includes 5 HP main drive with 176/1 ratio euro drive gearbox. Includes 5 HP water pump and heat exchan...

    Hainesport, NJ
  • Trusted Seller
    Johnson 78"

    Johnson 78"

    • Manufacturer: Johnson

    Used 78" Wide Johnson Heavy Duty Sheet Die. Serial #RW-1001-69.

    Hainesport, NJ
  • Trusted Seller
    EDI AutoFlex IV HR-75

    EDI AutoFlex IV HR-75

    • Manufacturer: EDI

    Used 60" EDI/Marshall & Williams Auto Flex model AutoFlex IV HR-75 flat film/sheet die mounted on a die cart supplied by Marshall & Williams giving a 56" center line height. bMarshall & Williams SN# 1190, MSO# 29...

    Hainesport, NJ
  • ENTEK 73 mm Twin Screw

    ENTEK 73 mm Twin Screw Extruder

    • Manufacturer: ENTEK

    ENTEK 73 mm Twin Screw Extruder Model E-73/52D Mfg 2012 400 Hp motor 600 Rpm screw speed Barrel design layout - 13 Barrels ( barrel material 73B ): Feed-inj-solid-solid-solid-vent-inj-inj-vent-inj-inj-vent-so...

    Tallahassee, FL
  • ENTEK 103 mm Twin Screw

    ENTEK 103 mm Twin Screw Extruder

    • Manufacturer: ENTEK

    ENTEK 103 mm Twin Screw Extruder ( 200 Operating Hours ) Model : E-103/56D Serial# 84908-10311 Mfg 4/2012 600 HP motor 1735 RPM 480 Volt 600 RPM screws Barrel design layout - 15 Barrels ( barrel material 73B...

    Tallahassee, FL
4041424344

Overview

Extruders are machines used in the manufacturing process to shape materials by forcing them through a die. Commonly used in plastic and metal industries, extruders are essential for creating products like pipes, sheets, and profiles. Their versatility allows them to handle various materials, including polymers, rubber, and even food products.

FAQ

What should I consider when buying a used extruder?

Evaluate the extruder's condition, age, and previous usage. Check for signs of wear, especially on the screw and barrel, and ensure the machine has been well-maintained.

How do I ensure the extruder is shipped safely to my location?

Hire a logistics company experienced in transporting heavy machinery. Make sure the extruder is properly secured, and all parts are protected from damage during transit.

What is the maintenance schedule for an extruder?

Regular maintenance includes inspecting the screw and barrel for wear, checking and replacing filters, and ensuring the cooling and heating systems are functioning properly. Follow the manufacturer’s guidelines for specific maintenance intervals.