- Trusted Seller
MATSUII DMZ-120
used
- Manufacturer: MATSUII
Used Matsui dehumidifying dryer. Model DMZ-120, Serial #01464, new 1995. Rated at 120 CFM. Has 3 KW heater, 230 volt, 3 phase, 60 hertz. Includes hopper mounted on a portable stand.
Hainesport, NJ - Trusted Seller
RANDCASTLE Ø51 мм × 203 мм
used
- Manufacturer: RANDCASTLE
Used 2" O.D. x 8" Wide Randcastle Sheet Extrusion 3-Roll Stack including Pull Roll Station and Single Position Winder.
Hainesport, NJ - Trusted Seller
2001 DAVIS STANDARD PEDESTAL
used
- Manufacturer: Davis-Standard
Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...
Hainesport, NJ 6″ Davis Standard 34:1 -500 HP -Vented (2 vents) Extruders (2 available)
used
- Manufacturer: Davis-Standard
6″ Davis Standard 34:1 -500 HP -Vented (2 vents) Extruders (2 available)
Rockville Centre, NY- Trusted Seller
2002 COPERION 2.3"
used
- Manufacturer: Coperion Waeschle
Used 58mm Coperion Co rotating Mega Compounder with 11 barrel sections (34/1 L/D) and side feeder, New 3/2002. Has electrically heated water cooled barrel. Direct connected to 500 hp DC motor with SCR controller....
Hainesport, NJ - Trusted Seller
BUSS 200 HP
used
- Manufacturer: Buss
Used 100mm Buss kneader with 9/1 L/D barrel. Driven by 200 hp DC motor, includes 5.94/1 gearbox, jacketed barrel and clam shell barrel opening. Includes operator control panel. Kneader will discharge into approxi...
Hainesport, NJ 
3.5″ Davis Standard 24:1-Air Cooled -N-Vented Extruders (3) 1998
used
- Manufacturer: Davis-Standard
3.5″ Davis Standard Extruders Model #MV35IN35 – New 1998 (Three Available) Air Cooled 24:1 L/D Non-Vented HP 158 Gear Ratio: 17.39 SF 1.25
Rockville Centre, NY75mm Davis Standard “Super Blue” Extruder 24:1 – Air Cooled 2013
used
- Manufacturer: Davis-Standard
Rockville Centre, NY- Trusted Seller
2003 WERNER & PFLEIDERER ZSK20
used
- Manufacturer: WP
- Model: ZSK20
Used 20mm Werner & Pfleiderer model ZSK20 co-rotating twin screw extruder. Has 40/1 L/D barrel at 43" centerline height driven through a 3:1 gearbox with a 37-Newton meter torque capacity per screw shaft. Extrude...
Hainesport, NJ - Trusted Seller
Conair D400H
used
- Manufacturer: Conair
- Model: D400H
Used Conair model D400H high heat desiccant dryer, 300 cfm. Have carousel desiccant cartridges, operator controls, no hopper. Previously used with 900-1000 lb hopper.
Hainesport, NJ - Trusted Seller
1997 Piovan T1000IX
used
- Manufacturer: Piovan
Used 1000 liter Piovan stainless steel drying hopper. New 1997. Hopper model T1000IX. Hoppers are approximately 36" diameter X 8' tall.
Hainesport, NJ - Trusted Seller
THORESON MCCOSH TD2000
used
- Manufacturer: Thoreson McCosh
Used 6,000 lb. Thoreson McCosh Desiccant Dryer Model TD2000. Serial #201-703-05. 480 volt, AC input, 20 hp. Amps 236.0, kw 182.0. No hopper included.
Hainesport, NJ - Trusted Seller
UNA-DYN GS150
used
- Manufacturer: Una-Dyn
Used Una Dyn Piovan Desiccant Dryer. Model GS150, serial #237240-01-01-0903. Rated at 150 cfm. Includes approximately 800 LB., 30" diameter x 72" straight side x 19" cone bottom insulated hopper with top mounted ...
Hainesport, NJ - Trusted Seller
PRODEX 4.5"
used
- Manufacturer: PRODEX
Used 4.5" pelletizing line consisting of the following: - 4.5" Prodex 34/1 L/D vented extruder including strand die, Lufkin "Change Gear" gearbox with 15.03/1 reduction, and an hydraulic screen changer with pump....
Hainesport, NJ 
Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled
used
- Manufacturer: Davis-Standard
10755162 Used Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled and non-vented barrel at nominal 44" center-line. 15.08:1 Gearbox reduction ratio; Rated at 1...
Belvidere, IL
Tip: Enter manufacturer, model or keyword
