Used Extruders

Trusted Seller
Lumber Tooling 6"
- used
- Manufacturer: Lumber Tooling
Used artificial lumber tooling previously used for various shapes. Approximately 6" in width.
Hainesport, NJ
Trusted Seller
FARRIS C550VT
- used
- Manufacturer: Farris
Used 7" x 22" Farris Solid Belt Puller Manufacturer: Farris Model: C550VT Rated at 4-74 feet per minute Has multi speed gearbox and variable speed transmission with manually adjusted belts
Hainesport, NJ
Trusted Seller
CLOEREN EBR III
- used
- Manufacturer: CLOEREN
Used Cloeren EBR III 56" wide cast film die body Serial #00-06613-17 1.25 x 4.75" rectangular feed entry 31 kw, 2450 lbs
Hainesport, NJ
Trusted Seller
MERRITT DAVIS 80
- used
- Manufacturer: Merritt Davis
Used 6" wide Merritt Davis model 80 solid belt puller supplying 80" belt contact length and approximately 8" of daylight on belts. Top and bottom belts are driven by drive shaft from 15 HP motor, and approximatel...
Hainesport, NJ
Trusted Seller
2011 LEISTRITZ LSB70
- used
- Manufacturer: Leistritz
Used 77mm Leistritz Twin Screw Side Feeder (Only) Manufacturer: Leistritz Model: LSB70 Year: 2011
Hainesport, NJ
Trusted Seller
1994 1994 Berstorff 125 HP 6 Meter x180MM Twin Screw Extruder Reactor
- used
1994 Berstorff N/A 125 HP 6 Meter x 180mm Twin Screw Extruder Reactor Consists of: 30,000 Flender process speed reducer Screws Barrel Die Outlet flange 2 heating zones 2 cooling zones 4 circulation pumps Shaft eq...
$675,000 USD
Tuscaloosa, AL
Trusted Seller
2-ROLL PULLER 6" DIA.
- used
- Manufacturer: 2-ROLL PULLER
Used 2-roll puller. 6" diameter X 10" long.with motor
Hainesport, NJ
Trusted Seller
2-ROLL PULLER 6" DIA.
- used
- Manufacturer: 2-ROLL PULLER
Used 2-roll puller. 6" diameter X 10" long. Rubber rolls with motor
Hainesport, NJ
Trusted Seller
FARRIS 8550F
- used
- Manufacturer: Farris
Used Farris 12" Wide x 30" Long Solid Belt Puller Manufacturer: Farris Model: 8550F Has manual belt adjustment, and variable speed transmission Rated 3-50 feet per minute
Hainesport, NJ
Trusted Seller
GOODMAN 3" Wide x 22" Long
- used
- Manufacturer: GOODMAN
Used Goodman Solid Belt Puller – Approx. 3" (76 mm) Wide x 22" (559 mm) Long Solid belt design with an approximate belt width of 3 inches (76 mm) and length of 22 inches (559 mm). Frame includes a provision for i...
Hainesport, NJ
Pre-Owned PRISM KX-16 R&D Twin-Screw Extruder – 1.25?kW Motor, Full Infrastructure
- used
- Manufacturer: PrismPrism
54037005 Used Thermofischer/PRISM 16 mm Eurolab Twin Screw Extruder. 16mm Diameter screws. 40:1 L/D. Maximum screw speed 500 RPM via a gearbox by a 1.25 kW motor. 7 housing sections. Electrically heated, water co...
Belvidere, IL
Coperian 30 mm – ZSK-30 – New 2010 Co-Rotating Twin Screw Extruder
- used
Coperian 30 mm – ZSK-30 – New 2010 Co-Rotating Twin Screw Extruder Screw Diameter 30mm L/D Ratio 30:1 Number of Zones: 9-1 Feed, 3 Vented, 1 Side Feeder & 4 non vented Includes Side Feeder 15 HP Water Cooling 4...
Rockville Centre, NY
Leistritz Micro18-GGL Twin Screw Pelletizing Line – Industrial Polymer Extruder
- used
- Manufacturer: Leistritz
40425043 Used Leistritz Twin Screw Pelletizing Line, Model Micro18-GGL. 18 mm Screws, counter rotating screws, 40:1 1/d, 500 rpm screw speed, electrically heated, water cooled barrel, 2.3 kw, 210/260 volt, 2950 r...
Belvidere, IL
Trusted Seller
Gatto DPC 107B 14-3
- used
- Manufacturer: Gatto
Used Gatto 14' long stainless steel 3-chamber differential pressure calibration/vacuum sizing tank. Model DPC 107B 14-3, Serial # 691891. Has 13" X 13" cross section, 2 pumps, and stainless steel reservoir. Missi...
Hainesport, NJ
Trusted Seller
AUTOMATED DOWNSTREAM EQUIPMENT 15'
- used
- Manufacturer: AUTOMATED DOWNSTREAM EQUIPMENT
Used 15' Automated Downstream Equipment stainless steel spray cooling tank. Has 11" x 11" cross section, 15' total length. Includes heat exchangers and filter. No pump included. Includes blower and air knife for ...
Hainesport, NJ